Festool SRM 212 LE-AS Mode D'emploi page 7

GB
Technical data
Power consumption
Connected load to appliance
plug socket max.
EC
CH, DK
GB
AUS
Volume flow (air)
Vacuum
Filter surface
Suction hose
Sound pressure level
in compliance with EN 60704-1
Container capacity
Dimensions LxWxH
Weight
Power cable length
Protection type
The specified illustrations can be found at the
beginning of the operating instructions.
Pictograms
Note, Danger!
Manual, read the instructions.
1 Intended use
- The vacuum cleaners are designed as
specified for the aspiration and evacuation
of noxious dusts industrial threshold limit
values (LTL-values) up to 0.1 mg/m³ and of
wood dusts corresponding to dust class ‘M’
in accordance with IEC 60335-2-69.
- The vacuum cleaners are designed as
specified for extracting water.
- The vacuum cleaners are designed in
accordance with EN 60335-1 and EN 60335-
2-69 for a higher loading in industrial use.
- The dust extractor has an electronically
commutated motor (EC motor).
The user is liable for damage and injury
resulting from incorrect usage!
1.1 Safety instructions
The appliance may contain dust that is
hazardous to health. The appliance
must not be emptied, nor must
maintenance work, including filter
changes, be carried out, by anyone
other than authorized specialist
personnel with appropriate protective
equipment. Do not operate the
appliance without a fully installed filter
system.
- When handling and extracting dusts that are
hazardous to health, the safety regulations
applicable in your country as well as the
specifications of the material manufacturer
must be observed without fail.
SRM 212 LE-AS
350 - 1,200 W
2,400 W
1,100 W
1,800 W
1,200 W
max. 240 m³/h
max. 23,000 Pa
10,100 cm²
Ø 27 mm x 3.5 m
59 dB(A)
50 l
460x440x695 mm
14.5 kg
7.5 m
IP 44
- Only use original Festool accessories.
- If used to extract dusts with LTL values or
large quantities of beech or oak sawdust,
only one dust source (electric or air tool) may
be connected.
- Do not use to extract aggressive liquids (e.g.
acids, alkalis, solvents).
- Remove plug from mains socket when not
in use and before maintenance work.
- Do not pull plug out of mains socket by its
cable.
- Protect the cable against heat, oil and sharp
edges.
- Check the plugs and cables regularly and have
them replaced by an expert if damaged.
- Do not leave devices out in the rain.
- Do not lift or carry the devices by their handles
using a crane hook or lifting gear.
- The device may only be used by persons who
have been trained in its use and who are
authorised to do so.
- For safety reasons, only operate the machine
using a totally earthed socket.
2 Appliance preparation and initial
operation
Stick the enclosed sticker in your national
language on the text area of the warning plate
(1.6).
2.1 Assembling the device
The accessories are delivered horizontal in the
container (1.4), and must be removed prior
to initial operation.
- Open locking clips (1.3), remove top section
(1.1),
- Insert filter bag as per instructions (see print
on filter bag). Important: Push filter bag
collar (3.2) onto intake fitting (3.1) with some
force.
- Replace top section of extractor and close
locking clips.
2.2 Electrical connection
The operating voltage shown on the
rating plate must correspond to the
voltage of the mains power supply.
Make sure that the vacuum cleaner is
switched off when you plug the power
cable in.
2.3 On/off switch (1.2)
In position 0 the vacuum cleaner is switched
off and the appliance plug socket (1.7) is dead.
Before switching on, make sure that a filter
element (2.2) and a filter bag (3.3) have been
properly inserted.
Two modes of operation are possible:
a) Switch position “MAN”
The appliance plug socket is live.
7