stayer CPT 3000 E Instructions D'emploi page 25

- Turn both fine adjustment screws (7) clockwise to
minimize the play between base plate and guide rail, if
necessary.
- Fasten the fine adjustment screws clockwise.
CONNECTING RODS FOR GUIDE RAILS
- To connect both guide rails slide the first connecting
rod from the bottom into the groove of the guide rail.
- Slide the other connecting rod into the second groove.
- Use the 3 mm Allen key to tighten the stud screws to
the limit stop to connect the rails.
GUIDE RAIL SPLINTER GUARDS
The guide rails come with a splinter guard (black protruding
rubber lip). The splinter guard should be cut to size before first
use. The splinter guard ensures a tear-free cut, since the wood
fibers at the top of the work piece are torn without splinter guard.
This is due to the saw blade teeth being directed upward.
After cutting the splinter guard to size it also shows the precise
cutting path of the saw blade.
- Mark a cutting line on the work piece and align the guide rail
exactly with this cutting line.
- Fix the guide rail with clamps on the work piece.
- Set the selector switch to marked cut function. Set the
plunge saw speed to 6.
- Place the plunge saw at the rear end of the guide rail.
- Switch the plunge saw on and push the saw down. Cut the
splinter guard continuously over the entire length. The edge
of the splinter guard now exactly matches the cutting edge.
KICKBACK STOP
The kickback stop is designed to prevent operator injuries
due to kickback.
When working with the guide rail the kickback stop (6)
automatically clicks into place on the base plate as
soon as the base plate is placed on the guide rail. The
kickback stop (6) counteracts the movement if you try to
guide the plunge saw on the guide rail back or if the saw
kicks back, e.g. due to the saw blade jamming.
- Turn the spring-loaded screw of the kickback stop (6)
towards 0 to manually unlock. Now the saw can be
moved forward and back.
- Release the spring-loaded screw for the kickback stop
to click into place on the guide rail again.
After a kickback always check the guide rail for damages
and dispose of a damaged guide rail to prevent accidents.
PLUNGE CUT WITH GUIDE RAIL
- Hold the plunge saw with both hands at hand grips (3)
and (4).
- Switch the plunge saw on and wait until it runs on full
speed.
- Push the saw slowly down and guide the saw towards
the plunge position.
Note: The cutting width markings (15) at the side of the
protective cover show the foremost and rearmost cutting
points of the saw blade at maximum cutting depth when
using the guide rail and a 165 mm diameter saw blade.
ENGLISH
25
CLEANING AND MAINTENANCE
Attention !Before performing any work on the
equipment, pull the power plug.
Cleaning
- Keep the ventilation slots of the machine clean to
prevent overheating of the engine.
- Regularly clean the machine housing with a soft cloth,
preferably after each use.
- Keep the ventilation slots free from dust and dirt.
- If the dirt does not come off use a soft cloth moistened
with soapy water.
Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may
damage the plastic parts.
Checking and replacing the carbon brushes
The carbon brushes must be checked on a regular basis.
- In case of wear, replace both carbon brushes at the same
time.
- Mount the carbon brush holders.
- After mounting new carbon brushes, let the machine run at
no load for 15 minutes.
Use only the correct type of carbon brushes.
Lubrication
- From time to time, apply a drop of oil to the thread of the
lock screw (17).
Repair service
Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.
Warranty
Warranty card
lncluded in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and retum to vendar with a copy
of purchasing receipt or invoice and you should receive a
receipt.
Note: lf you cannot find the warranty card within
the documentation,youmust ask for it through your
supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired otherthan themanufacturer.
Disposal and recycling
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
25