BFT LIBRA-MA-R Instructions D'utilisation Et D'installation page 16

ACCESS TO MENUS
Press the OK key
OK
BFT
Control unit software version
LIBRA1. 0
No. total manoeuvres
OK
0000
(in thousands)
0000
No. manoeuvres since latest
00 maintenance(in thousands)
No. radio control devices
memorised
+/-
PARAM
OK
+/-
END
- +
+/-
LOGIC.
OK
+/-
END
- +
FOLLOWING MENUS
FIG. B
16 - LIBRA-MA-R - Ver. 04
8888
[ 00 ]
Preset value
Parameter increment/reduction
/ON
/OFF
or ON/OFF commutation
Press OK key (Enter/confirm)
OK
Menu scrolling
- +
(+ = preceding - = following)
TCA
OK
- +
m1 t
OK
- +
m2 t
OK
- +
m1 t slow
OK
- +
m2 t slow
OK
- +
open delay time
OK
- +
cls delay time
OK
- +
m1 fast time
OK
- +
m2 fast time slov speed
OK OK
- +
slov speed
OK
- +
zone
OK
TCA [oFF]
OK
- +
3 step
[off]
OK
- +
ibl open
OK [off]
- +
fast cls
[off]
OK
- +
photoc. open [off]
OK
- +
TEST PHOT [off]
OK
- +
[off]
SCA 2ch
OK
- +
[off]
i Mot ON
OK
- +
[off]
BLOC persist
OK
- +
[off]
hold-to-run
OK
- +
[off]
fixed code
OK
- +
[on]
radio prog
OK
- +
[off]
master
OK
- +
[off]
start open
OK
Fig. A
+
OK
[0010]
OK
[0050]
OK
[0050]
OK
[0045]
OK
[0045]
OK
[0010]
OK
[0010]
OK
[0050]
OK
[0002]
[0050]
OK OK
[0002]
OK
[0000]
OK
ON PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
ON
PRG
OK
OFF
LEGENDA
+/- Simultaneously press the + and - keys.
Simultaneous pressure of the + and – keys
allows you to exit the active menu and return
to the preceding menu; if this takes place at
the main menu level, programming is exited
and the display switched off.
The modifications made are only confirmed if
the OK key is subsequently pressed.
PRG
Message: Programming in progress
Message: KO! (value or function error)
Message: "Wait" (enter value or function)
PRG
PRG
PRG
PRG
PRG
PRG
PRG
PRG
PRG
PRG
PRG
PRG
PARAMETER MENU
TCA (automatic closing time)
value expressed in seconds
(default 10=10s, min 3=3s, max 60=60s)
Motor 1 torque value expressed in %
(default 50%, min 1%, max 99%)
Motor 2 torque value expressed in %
(default 50%, min 1%, max 99%)
Motor 1 torque slow-down
value expressed in %
(default 45%, min 1%, max 99%)
Motor 2 torque slow-down
value expressed in %
(default 45%, min 1%, max 99%)
Opening phase-difference Time
value expressed in tenths of a second
(default 10=1s, min 10=1s, max 100=10s)
Closing phase-difference Time
value expressed in tenths of a second
(default 10=1s, min 10=1s, max 10=10s)
Motor 1 slow-down speed time
value expressed in seconds
(default 5=5s, min 1=1s, max 30=30s)
Motor 2 slow-down speed time
value expressed in seconds
(default 5=5s, min 1=1s, max 30=30s)
Slow-down speed
0= Slow-down disabled
1= 50% of normal speed
2= 33% of normal speed
3= 25% of normal speed
Zone numerical value
(default 0, min 0, max 127)