Troubleshooting - Pit Boss PB150PPS Assemblage Et Fonctionnement

Proper cleaning, maintenance and the use of clean, dry, quality fuel will prevent common operational problems. When your Pit
Boss® grill is operating poorly, or on a less frequent basis, the following troubleshooting tips may be helpful. For FAQ, please visit
www.pitboss-grills.com . You may also contact your local Pit Boss® authorized dealer or contact Customer Service for assistance.
WARNING: Always disconnect the electrical cord prior to opening the grill for any inspection, cleaning,
maintenance or service work. Ensure the grill is completely cooled to avoid injury.
PROBLEM CAUSE
No Power Lights Temperature Control
On The Control Dial is still off.
Board
Not Connected To
Power Source
Fuse Blown On The
Control Board
The GFCI outlet has
been tripped.
Faulty Control Board
Fire in Burn Pot Auger Not Primed
Will Not Light
Auger Motor Is
Jammed
Igniter Failure
Insufficient Air Flow
Through Burn Pot
Flashing Dots On The Igniter Is On
LCD Screen
Flashing Grill Temperature Is
Temperature On Below 65°C /150°F
LCD Screen
20

TROUBLESHOOTING

SOLUTION
Turn the Temperature Control Dial to a temperature setting.
Ensure unit is plugged into a working power source. Reset breaker. Ensure GFCI is a minimum
10 Amp service (see Electric Wire Diagram for access to electric components) Ensure all wire
connections are firmly connected and dry.
Remove hopper access panel (see Electric Wire Diagram for diagram), press in plastic tabs
holding the control board in place and carefully pull controller inside the hopper to release
controller. Check the fuse for a broken wire or if the wire has turned black. If yes, fuse needs
to be manually replaced.
Ensure GFCI is a minimum 10 Amp service.
Control Board needs to be replaced. Contact Customer Service for a replacement part.
Before the unit is used for the first time or anytime the hopper is completely emptied out,
the auger must be primed to allow pellets to fill the auger tube. If not primed, the igniter will
timeout before the pellets reach the Burn Pot. Follow Hopper Priming Procedure .
Remove cooking components from the main barrel. Press the Power Button to turn the unit
on, turn Temperature Control Dial to SMOKE, and inspect the auger feed system. Visually
confirm that the auger is dropping pellets into the Burn Pot. If not operating properly, call
Customer Service for assistance.
Remove cooking components from the main barrel. Press the Power Button to turn the unit
on, turn Temperature Control Dial to SMOKE, and inspect the igniter. Visually confirm that
the igniter is working by placing your hand above the Burn Pot and feeling for heat. Visually
confirm that the igniter is protruding approximately 13mm / 0.5 inches in the Burn Pot. If not
operating properly, follow Manual Start-up Procedure to continue use of grill; however, call
Customer Service for assistance or a replacement part.
Check Burn Pot for ash build-up or obstructions. Follow Care and Maintenance instructions
for ash build-up. Check fan. Ensure it is working properly and air intake is not blocked. Follow
Care and Maintenance instructions if dirty.
This is not an error that effects the grill. Used to show that the unit has power and is in Start-
Up mode (igniter is on). The igniter will turn off after five minutes. Once the flashing dots
disappear, the grill will begin to adjust to the desired temperature selected.
This is not an error that effects the unit; however, it is used to show that there is some
risk that the fire could go out. Check hopper for sufficient fuel or if there is an obstruction
in the feed system. Remove pellets and follow Care and Maintenance instructions. Check
grill temperature probe and follow Care and Maintenance instructions if dirty. Check Burn
Pot for ash build-up or obstructions, and follow Care and Maintenance instructions for ash
build-up. Check fan. Ensure it is working properly and air intake is not blocked. Follow Care
and Maintenance instructions if dirty. Check auger motor to confirm operation (rotation),
and ensure there is no blockage in the auger tube.