Barco F400 Manuel De Sécurité page 6

Safety Information
larger source and lower radiance value than native laser light. Nevertheless, when RG3, the projected light
represents a significant risk for the human eye when exposed directly within the beam. This risk is not
specific related to the characteristics of laser light but solely to the high thermal induced energy of the light
source; which is comparable with lamp based systems. When RG3, thermal retinal eye injury is possible
when exposed within the Hazard Distance. The Hazard Distance (HD) is defined from the projection lens
surface towards the position of the projected beam where the irradiance equals the maximum permissible
exposure as described in the chapter "High brightness precautions: Hazard distance".
• Always switch off the projector and disconnect from the mains power supply before attempting to remove
any of the projector covers or access parts inside the projector.
• This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics
inside the housing or compartments will violate any warranties and may be hazardous.
• For correct physical installation, refer to the Installation manual.
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious
damage to it and possible injury to the user.
• Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.
• Cooling liquid circuit. The projector contains a cooling circuit filled with Mono-ethylene glycol (1,2-ehtane
diol) and inhibitors in aqueous solution (34% active). If the unlikely event that the cooling circuit have a
leak, switch off the device nd contact qualified service personnel. The liquid is not for househols use. Keep
out of range of children.. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact with
eyes, skin and clothing. Avoid inhaling the noxious fumes.
To prevent fire hazard
• Barco projection products are designed and manufactured to meet the most stringent safety regulations.
This projector radiates heat on its external surfaces and from ventilation ducts during normal operation,
which is both normal and safe. Exposing flammable or combustible materials into close proximity of this
projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is
absolutely necessary to leave an "exclusion zone" around all external surfaces of the projector whereby no
flammable or combustible materials are present.
• Do not place flammable or combustible materials near the projector!
• Caution! Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than
25 cm (10") to the exhaust vent.
• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the
projector and to protect it from overheating, these openings must not be blocked or covered.
• The openings should never be blocked by placing the projector too close to walls, or other similar surface.
Allow for sufficient distance to walls and ceilings to avoid overheating. Minimum safety distance to the
exhaust area of the unit must not be less than 25 cm (10") and to the intake area, not less than 25 cm (10").
• This projector should never be placed near or over a radiator or heat register.
• This projector should not be placed in a built-in installation or enclosure unless proper ventilation is
provided.
• Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable
and combustible materials away from the projector at all times.
• Mount the projector in a well-ventilated area away from sources of ignition and out of direct sun light.
Always allow ample airflow through the projector.
• Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder fire
extinguishers.
• Never use water on an electrical fire.
• Always have service performed on this projector by authorized Barco service personnel. Always insist on
genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety
of this projector.
• Projection rooms must be well ventilated or cooled in order to avoid heat buildup.
• Let the projector cool down completely before storing. Remove cord from the projector when storing.
To prevent battery explosion during board service
• Danger of explosion if battery is incorrect installed.
• Replace the battery with the same or equivalent type recommended by the manufacturer.
• For disposal of used batteries, always consult federal, state, local and provencial hazardous waste
disposal rules and regulations to ensure proper disposal.
6 R5914422 /00 F400