Yamaha Clavinova CVP-79A Mode D'emploi page 130

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2.1.5 Other Parameter Changes
2.1.5.1 Master Tuning
11110000 F0
01000011 43
0001nnnn 1n
00100111 27
00000001 30
00000000 00
00000000 00
0mmmmmmm mm
0lllllll ll
0ccccccc cc
11110111 F7
Changes tuning of all channels.
2.1.5.2 Channel Detune
11110000 F0
01000011 43
0001nnnn 73
00111001 39
00010001 11
0000nnnn 0n
01000011 43
0vvvvvvv vv
11110111 F7
The Channel Detune message only affects the specified channel.
2.1.5.3 Volume and Expression Realtime Control Off
11110000 F0
01000011 43
0001nnnn 73
00111001 39
00010001 11
0000nnnn 0n
01000101 45
0vvvvvvv vv
11110111 F7
When "On" is received subsequent volume and expression changes are only
valid during key on. Normal operation resumes when "Off" is received.
2.2 Bulk Dump
The CVP 79A/69/69A/59S models support the following parameters.
[XG NATIVE ]
1) XG System Data
2) Multi Effect1 Data
3) Drums Setup Data
2.2.1 XG Native Bulk Data
11110000 F0
01000011 43
0000nnnn 0n
01001100 4C
0bbbbbbb bbbbbbb
0bbbbbbb bbbbbbb
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
00000000 00
| |
| |
0ccccccc ccccccc
11110111 F7
For information about "Address" and "Byte Count" fields, refer to attached
tables.
In the attached tables "TOTAL SIZE" partitions a data series into single bulk
dumps. The "address" is the first byte of the bulk data.
The checksum value is set such that the sum of Byte Count, Address, Data, and
Checksum has value zero in its seven least significant bits.
If too much bulk data is received at a time there is a chance of error. The total
data for a bulk dump should not exceed 512 bytes, it is recommended that data
be kept under 512 bytes with an interval time of 120msec or more between 512
byte bulk.
Exclusive status
YAMAHA ID
When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
Model ID
Sub ID
Master Tune MSB
Master Tune LSB
End of Exclusive
Exclusive status
YAMAHA ID
Clavinova ID
CVP-79A/69/69A/59S ID
Sub ID
n = MIDI Channel
Dual Detune
Value vv: $00 - $40 - $7F (-64 - 0 - +63)
End of Exclusive
Exclusive status
YAMAHA ID
Clavinova ID
CVP-79A/69/69A/59S ID
Sub ID
n = MIDI Channel
Volume and Expression Realtime Control Off
Value vv: $00:Off $7F:On
End of Exclusive
Exclusive status
YAMAHA ID
When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
Model ID of XG
ByteCount
ByteCount
Address High
Address Mid
Address Low
Data
Check sum
End of Exclusive
2.2.1.1 XG System Data bulk dump
See Tables 1-1, 1-2.
2.2.1.2 Multi Effect1 Data bulk dump
See Tables 1-1, 1-3.
2.2.1.3 Drums Setup Data bulk dump
See Tables 1-1, 1-5.
2.3 Parameter Request
The CVP 79A/69/69A/59S models support the following request for
parameters covered by Parameter Change specifications.
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0011nnnn 3n When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
01001100 4C Model ID of XG
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
11110111 F7 End of Exclusive
If the parameter's data size is 2 or 4. The Parameter Request address for that
parameter is the first byte of the bulk.
2.4 Dump Request
The CVP 79A/69/69A/59S models support the following request for data
covered by bulk dump.
11110000 F0 Exclusive status
01000011 43 YAMAHA ID
0010nnnn 2n When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
01001100 4C Model ID of XG
0aaaaaaa aaaaaaa Address High
0aaaaaaa aaaaaaa Address Mid
0aaaaaaa aaaaaaa Address Low
11110111 F7 End of Exclusive
For more information on the "Address" field, refer to the attached table.
In the attached tables "TOTAL SIZE" partitions a data series into single bulk
dumps. The "address" is the first byte of the bulk data.
3. Realtime Messages
3.1 Active Sensing
a) Transmission
Transmitted approximately once every 200msec.
b) Reception
If no MIDI data is received within 400ms following receipt of FE, the unit
executes processing equivalent to ALL SOUND OFF, ALL NOTES OFF, and
RESET ALL CONTROLLERS, then clears any remaining FEs.
3.2 MIDI Clock
a) Transmission
Transmitted as 1/96 clocks.
b) Reception
If the [MIDI 1] clock function is set to the External mode it will receive a
resolution of 1/96 clocks.
3.3 Start/Stop
If the [MIDI 2] function Start/Stop filter is ON transmission and reception are
disabled.
a) Transmission
All rhythm start and stop signals are transmitted.
b) Reception
When the relative message is received, the rhythm or song will start or stop.
127