Operation - Wolf Garten Power Edition 40 E-1 Mode D'emploi

Mount the collecting bag
1. Place the chute (1) on the collecting bag flap (2)
2. Press the chute from behind onto the collecting bag flap. The
chute is ready for use as soon as it locks into place

Operation

General
Operating times
z Please check noise abatement regulations prevailing in your
country.
Feed cable through the strain relief
z Please feed cable through the strain relief
3
Note: WOLF-Garten Flick-Flack®
WOLF-Garten Flick-Flack® keeps the cable away from the
cutting unit J .
Set cut height
1
Attention! Rotary cutter blade
Undertake work/adjustments on the equipment only after
the motor is switched off and the cutting tool has come to a
standstill.
K
1. Pull the lever out (1).
2. Set the desired cutting height
3. Press the lever back in
Selection of Cutting height
z If possible, mow when grass is dry in order to protect turf. Do
not se cutting position too low when mowing very hight or wet
grass.
z We recommend an average cutting height of 50 mm.
Connecting to the mains (230 Volts, A.C., 50 Hz)
z The mower operates from any normal household mains sup-
ply, provided with a 16 Amps. fuse.
3
Note: Residual current protection device
These protection devices safeguard while touching
damaged wires, from insulation flaws and in certain cases,
also while damaging live wires.
z We recommend that the equipment only be plugged into
a power socket, which is protected by a residual current
protection device (RCD) with a residual current of not
more than 30 mA.
z Retrofit kits are available for old installations. Consult an
electrician.
Starting and Stoping
z Switch on motor with mowerplaced on level and firm ground.
z not in high grass - alternatively tilt slightly
Switch-on motor N
1. Depress button and hold (1).
2. Lift up bar (2).
3. Release bar (1).
Wheel drive on (Power Edition 40 EA-1)
z Raise drive bracket (3).
12
E F G
E
H
H
.
L .
K (2).
M
.
N
F
.
G
.
Wheel drive off (Power Edition 40 EA-1)
z Release drive bracket (3).
Switch-off motor
z Release bar (2).
Tips for mowing
z To prevent strips of grass from being left unmowed, the cutting
paths must always overlap a few centimeters
z Always let cable trail on the cut side of the lawn.
Cut / Collect
Activate cut/collect function
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
z Do not start the motor until your feet are at a safe
distance from the cutting tool.
1. Remove the grass collecting bag.
2. Turn the switch to "CUT/COLLECT".
3. Hang up the collection bag if necessary.
4. Start the motor.
Hang up collection bag
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
1. Lift the protective flap.
2. Hang the grass bag in the chassis with the hooks in the re-
cesses (see arrow).
3. Replace the protective flap.
Emptying of Grassbox
When the collection bag is full, the flap lowers by itself
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
z Empty collection bag.
z Remove potential blockages in the cutting space before
starting.
3
Instructions for level indicator:
For an efficient functioning of the level indicator, regularly
clean the holes under the level indicator in the collection
bag with a hand brush.
N
N
P
Q
O
.
R .
G