Cleaning; Troubleshooting - Vollrath Mirage 74701DW Manuel D'utilisation

CLEANING

WARNING
Electrical Shock Hazard
Keep water and other liquids from entering the inside of the
equipment. Liquid inside the equipment could cause an
electrical shock. Do not spray water or cleaning products.
Liquid could contact the electrical components and cause a
short circuit or an electrical shock.
CAUTION
Burn Hazard
Hot surfaces and food can burn skin. Allow the hot surfaces to
cool before handling. Do not drop or spill water onto the
cooking surface as it can spray or splatter.
To maintain the appearance and increase the service life, clean this
equipment daily.

TROUBLESHOOTING

Problem
The equipment is on, but not heating
and the display is flashing.
Alarm is sounding.
The equipment suddenly stopped
working.
Display
Message Cause
The inset is not a Vollrath induction-ready inset or is the wrong size
Bad Pan
Vollrath induction-ready inset.
If the equipment is turned off, this is normal. It indicates the equip-
ment is still hot.
HOT
If the equipment is in use, the inset may be too hot.
F-2 The inset may be too hot.
F-1
The equipment may have overheated.
F-8
Other error
Internal error.
codes
®
Mirage Drop-in Induction Warmers and Rethermalizers Operator's Manual
Might be Caused By
The inset is not a Vollrath induction-ready
inset or is the wrong size Vollrath induction-
ready inset.
Trouble with the electrical connection is
causing low input voltage.
An error.
The equipment may be too close to an exter-
nal heat source or the air intake may be
restricted.
The inset may be too hot.
What you will need:
• Three soft clean cloths, one each for cleaning, rinsing and drying
• Mild dish washing detergent
• Clean warm water
NOTICE: Failure to follow these cleaning instructions may lead to
product damage that will not be covered under warranty.
1. Unplug the equipment and let it completely cool.
2. Use a soft cloth moistened with warm water and a mild dish washing
detergent to clean the well and the rim.
NOTICE: Do NOT use cleaning solutions that contain chlorine or
bleach ingredients. Use of solutions with these
ingredients will damage the well and will void the
.
warranty
3. Use the second clean soft clean soft cloth moistened with clean
warm water to wipe all detergent from the well and the rim.
4. Use the third soft clean cloth to dry the well and the rim.
NOTICE: Failure to throughly remove all detergent or thoroughly
dry the equipment may result in damage to the
equipment.
5. The stainless steel insert is dishwasher safe.
Course of Action
Replace the inset with the correct size Vollrath induction-ready
inset for the equipment. Vollrath induction-ready insets are
stamped "Induction Ready." Reset the equipment by turning it
OFF and then ON.
Make sure the plug is fully inserted into an electrical outlet that
matches the rating on the equipment's nameplate.
Make sure the electrical circuit is not overloaded.
See the Display Messages in the table below.
Relocate the equipment away from external heat sources. Clear
any obstructions to the air intake. Contact Vollrath Technical
Services if the problem persists.
Remove the inset. Allow the inset and equipment to cool before
resuming use. Contact Vollrath Technical Services if the prob-
lem persists.
Course of Action
Replace the inset with the correct size Vollrath induction-ready
inset for the equipment. Vollrath induction-ready insets are
stamped "Induction Ready." Reset the equipment by turning it
OFF and then ON.
Allow the equipment to cool (about 5-10 minutes) before clean-
ing.
Remove the inset. Allow the inset and equipment to cool before
resuming use. Do not place excessively hot food into the inset.
Do not an place excessively hot inset into the equipment. Con-
tact Vollrath Technical Services if the problem persists.
Remove the inset. Allow the inset and equipment to cool before
resuming use. Do not place excessively hot food into the inset.
Do not an place excessively hot inset into the equipment. Con-
tact Vollrath Technical Services if the problem persists.
Relocate the equipment away from external heat sources. Clear
any obstructions to the air intake. Contact Vollrath Technical
Services if the problem persists.
Contact Vollrath Technical Services.
5