Scheppach capas 2 Mode D'emploi page 7

SETTINGS
Inside corner Mitre Angle
Bevel Angle
Moulding
Position
Finished
side
Outside corner Mitre Angle
Bevel Angle
Moulding
Position
Finished
side
Pullover Cut
WARNING:
1. Never pull the cutting head assembly and spin-
ning blade towards you during the cut. The blade
may try to climb up on the top of the workpiece,
causing the cutting head assembly and spinning
blade to kick back.
2. Never lower the spinning saw blade down be-
fore pulling the cutting head to the front of the
saw.
1. Unlock the carriage ➀ with the lock handle ➁ and al-
low the cutting head assembly to move freely. (Fig.
14)
2. Move the mitre handle and cutting head to the de-
sired mitre angle and bevel angle according to the
mitre cut and bevel cut procedures.
3. Grasp the saw handle and pull the carriage forward
until the centre of the saw blade is over the front of
the work piece.
4. Activate the switch, then press the blade guard lock
lever to lower the cutting head down.
5. When the saw reaches full speed, push the saw han-
dle down slowly, cutting through the leading edge of
the workpiece.
6. Slowly move the saw handle toward the fence, com-
pleting the cut.
7. Release the switch and allow the blade to stop spin-
ning before allowing the cutting head to raise.
Carrying the Tool
1. Loosen the mitre lock knob and turn the table all the
way to the right. Lock the table at 45° mitre angle.
2. Pull the cutting head to the front of the saw, then
lock the carriage.
3. Lower the cutting head and push in the lock pin.
4. Carry this mitre saw with the built-in carry handle and
the side of the base.
Changing Blades
Fig. 18 and 19
WARNING: To avoid injury from accidental starting,
always turn the switch off and remove the power plug
from the power source before changing the blades.
Left Side Right Side
31.6° Right 31.6° Left
33.9° 33.9°
top against bottom against
fence fence
Keep left side Keep left side
of cut of cut
31.6° Left 31.6° Right
33.9° 33.9°
bottom top
against fence against fence
Keep right Keep right
side of cut side of cut
1. Loosen the cover screw ➀.
2. Rotate the arbor bolt cover ➁ up and back to reveal
the arbor bolt ➂.
3. Locate the arbor lock latch ➅ on the backside of the
motor. Place a blade wrench ➃ over the arbor bolt.
4. Place the arbor lock latch and hold it in firmly while
turning the wrench clockwise. The arbor lock will en-
gage after turning the wrench.
5. Remove arbor bolt, arbor washer and outside flange.
Note:
Pay attention to the parts removed, noting their
position and the direction they face.
6. Whipe the outside flanges clean before mounting a
new blade.
7. Install the new 216 mm blade ➄, making sure the ro-
tating arrow matches the clockwise rotation arrow on
upper guard.
8. Install the outside flange, arbor washer and arbor
bolt. Press the arbor lock and turn the blade wrench
counterclockwise to secure the blade.
9. Restore the arbor bolt cover to its original position.
Replace the cover screw and securely tighten.
Optional Accessories
Art. No. No. of
Teeth
88001800 42
88001801 60
88001802 60
Maintenance
WARNING: For your own safety, turn the switch off
and remove the plug from the power source outlet
before maintaining or lubricating your mitre saw.
General Maintenance
Occasionally use a cloth to wipe off chips and dust from
the machine. Oil the rotary parts once a month to extend
the tool life. Do not oil the motor.
Brush Inspection
Check the motor brushes after the first 50 hours of use for
a new machine or after a new set of brushes have been in-
stalled. After the first check, examine them every 10
hours of use.
When the carbon is worn to 6 mm in length or if the spring
or shunt wire is burned or damaged, replace both brushes.
If the brushes are found serviceable after removing, rein-
stall them.
Tooth Dimensions
Style
ATB ø 30 mm Bore,
ø 305 mm O. D.
WZ ø 30 mm Bore,
ø 305 mm O. D.
TFZ ø 30 mm Bore,
ø 305 mm O. D.
4