Bosch 0 607 459 203 Notice Originale page 16

OBJ_BUCH-1578-004.book Page 16 Monday, October 10, 2016 1:03 PM
16 | English
Pneumatic straight screwdriver
Article number
No-load speed
Output power
Maximum torque
Max. screw diameter
Right/left rotation
Tool holder
Lever start
Thrust-start
Shut-off clutch
S-Plus clutch
Max. working pressure for tool
Thread size of hose connection
Inner diameter of hose
Recommended hose length
Air consumption at no-load
Weight according to EPTA-Procedure 01:2014
Noise/Vibration Information
Sound emission values determined according to
EN ISO 15744.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K = 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 28927.
Screwdriving without impact: a < 2.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN ISO 11148 and may be used to compare one
pneumatic tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the pneumatic tool. However if the pneumatic
tool is used for different applications, with different accesso-
ries or insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase the expo-
sure level over the total working period.
An exact estimation of the level of exposure to vibration
should also ta
ke into account the times when the pneumatic tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintaining the pneu-
matic tool and the accessories, keeping the hands warm, or-
ganisation of work patterns.
1 609 92A 37J | (10.10.16)
0 607 459 ...
-1
min
W
Nm
mm
mm
bar
psi
mm
m
l/s
cfm
kg
lbs
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical data" complies with all applicable
provisions of the directive 2006/42/EC including its amend-
ments and is in conformity with the following standards:
EN ISO 11148-6.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
2 2
, K=1.5 m/s .
Executive Vice President
Engineering
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Suspension Device
 If you want to operate the pneumatic tool in a suspen-
sion device, take care to fasten it in the device first be-
fore connecting it to the air supply. This measure pre-
vents accidental starting of the tool.
With the utility clip 4, you can fasten the pneumatic tool to a
suspension device.
Exhaust-air Guidance
With exhaust-air guidance, the exhaust air can be diverted
through an exhaust-air hose away from your workplace, while
0 607 459 ...
... 203 ... 204
800 800
20 20
0.06–1 0.06–1
M 3 M 3
 
3 3

–
 

–

–
6.3 6.3
91 91
M 5 M 5
4.0 4.0
4.0 4.0
3.0 3.0
6.4 6.4
0.23 0.23
0.4 0.4
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools
0 607 459 ...
... 205
1200
20
0.06–0.8
M 3

3
–


–
6.3
91
M 5
4.0
4.0
3.0
6.4
0.23
0.4