Tone (Bass/Treble Settings); Metal Telescopic Antenna; Languages; Software Version - PERFECTPRO WORK-STATION Manuel De L'utilisateur

Press the Menu button, and then rotate the Tuning knob until the display shows
2.
"System".
3. Press the Tuning knob; rotate the Tuning knob until the display shows "Loudness".
4. Rotate the Tuning knob to select between "Loudness On" or "Loudness Off". Press
the Tuning knob to confirm the setting and return to normal display.
TONE
The Tone function enables the user to adjust the lower and higher sound frequencies.
1. Press the On/Off button to turn on the radio.
2. Press the Volume knob, the display shows "BASS 0".
3. Rotate the Volume knob to set the desire Bass level.
4. Press the Volume knob to confirm, the display shows "TREBLE 0".
5. Rotate the Volume knob to set the desire Treble level.
6. Press the Volume knob to confirm and return to normal display.

METAL TELESCOPIC ANTENNA

You can use this as an alternative antenna for your radio in areas or locations where the
radio signal (FM/DAB/DAB+) is weak to very weak.
ATTENTION: The standard antenna on the radio is flexible. The metal antenna
is not flexible or bendable and should be used with care. Breaking or bending
antennas is not covered by warranty.
Installing: Carefully screw off the standard flexible antenna. First carefully loosen the
antenna with an open-end-wrench key (size 14) – turn counter clockwise. Carefully
screw on the metal telescopic antenna and softly tighten it with an open-end-wrench key
(size 14) – turn clockwise.
ATTENTION: do not use too much force when fixing the antennas as this can
damage the screw threat of the antennas or make it break off

LANGUAGES

The menu of the radio can be configured to various languages.
1. Press the On/Off button to turn on the radio.
2. Press the Menu button, and then rotate the Tuning knob until the display shows
"System".
3. Press the Tuning knob; rotate the Tuning knob until the display shows "Language".
4. Press the Tuning knob to enter the language adjustment menu.
5. Rotate the Tuning knob until the desired language appears on the display (default
is English).
13
Press the Tuning knob to confirm your choice. The display menu will change to the
6.
chosen language.

SOFTWARE VERSION

The software display cannot be altered and is just for your reference. You can only view
the software version in DAB and FM mode.
1. Press the On/Off button to switch on the radio.
2. Press the Source button to select FM or DAB mode.
3. Press the Menu button until the display shows "Full Scan", and then rotate
the Tuning knob until the display shows "System".
4. Press the Tuning knob; rotate the Tuning knob until the display shows
"SW version".
5. Press the Tuning knob to view the software version.
6. Press the Tuning knob to back to last menu and press menu to return to
the normal radio display.
Note: USB socket inside battery compartment is for upgrading the software of the device
if needed.

SYSTEM RESET

If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the On/Off button to switch on the radio.
2. Press the Menu button,
3. Rotate the Tuning knob until the display shows "System". Press the Tuning knob.
4. Rotate the Tuning knob until the display shows "Factory reset". Press the
Tuning knob.
5. Rotate the Tuning knob to select between "Yes" or "No". Select "Yes" if you wish
to reset the radio, otherwise, select "No".
6. Press the Tuning knob to cause the factory reset.
7. A full reset will be performed. All presets and the station list will be erased.
All settings will be set to the default values. The display will show "WELCOME
TO DIGITAL RADIO" for a few seconds, and then the radio will automatically
perform an auto scan of the Band III DAB channels and the FM band, the display
will show "Scanning" at DAB and "Auto" at FM.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
remove and reconnect all batteries and the power supply.
GB
G B
14