Know Your Product; Operation - SPARKY PMW 1212CE Notice Originale

c) Do not position your body in the area
where power tool will move if kickback
occurs. Kickback will propel the tool in di-
rection opposite to the wheel's movement
at the point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to
snag the rotating accessory and cause loss
of control or kickback.
Safety Warnings Specific for Polishing
Operations
a) Do not allow any loose portion of the
polishing bonnet or its attachment
strings to spin freely. Tuck away or trim
any loose attachment strings. Loose and
spinning attachment strings can entangle
your fingers or snag on the workpiece.
Safety Warnings Specific for Wire
Brushing Operations
a) Be aware that wire bristles are thrown
by the brush even during ordinary op-
eration. Do not overstress the wires by
applying excessive load to the brush.
The wire bristles can easily penetrate light
clothing and/or skin.
b) If the use of a guard is recommended for
wire brushing, do not allow any interfer-
ence of the wire wheel or brush with the
guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal
forces.
V - Know your product
Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Spindle
2. Front handle
3. Spindle lock button
4. Driving machine
5. ON/OFF switch
6. Screw
7. Disperser
8. Tap lever
9. Support flange
10. Flexible backing pad M14
11. Brush (CMW 1212CE)
Original instructions
12. Seeger circlip (CMW 1212CE)
13. Guard (CMW 1212CE)
14. Spring (CMW 1212CE)
15. Shaft (CMW 1212CE)
16. Thumbwheel for electronic speed pre-se-
lection
17. Cleaning pad for wet processing made of
nonwoven fabric with hook-and-loop fastening
(CMW 1212CE)
18. Diamond particle pad for wet processing
with hook-and-loop fastening (PMW 1212CE)
ACCESSORIES AND OPERATING
TOOLS TO BE USED WITH THIS
POWER TOOL
PMW 1212CE
Diamond particle pad for wet processing with
hook-and-loop fastening, up to Ø200mm;
Flexible backing pad with hook-and-loop fas-
tening, M14, Ø180mm.
CMW 1212CE
Cleaning wheel brushes for wet processing
up to Ø200mm, M14, with or without abrasive
particles on the wires;
Cleaning pad for wet processing made of non-
woven fabric with hook-and-loop fastening,
up to Ø200mm;
Flexible backing pad with hook-and-loop fas-
tening, М14, Ø180mm.
VI - Operation
This power tool is supplied from single-phase
alternating current mains only. It is double in-
sulated, but when operated with PRCD the
power tool features safety class I according to
EN 60745-1 and IEC 60745-1 and MUST NOT
be connected to sockets without protective ter-
minals. This power tool is radio suppressed in
compliance with EMC Directive 2004/108/EC.
Model PMW 1212CE is designed mainly for pol-
ishing marble, granite, mosaics and natural ma-
terial facade cladding, requiring the use of liquid
feed system. After processing with appropriate
accessories the surface becomes smooth and
bright.
Model СMW 1212CE is designed mainly for
cleaning stone clad facades and floors by means
of brushes and FIBRAT pads requiring the use
of liquid feed system.
This power toll is not designed for CUTTING or
SANDING!
7
EN