Publicité
Les langues disponibles
Les langues disponibles
Here are some of the possibilities:
- expansion of number of entry panels
and internal extension per block;
- customization of system activation
time and duration of call;
- programming of all internal exten-
sions by software. In this case it is nec-
essary to collect the ID codes and to
insert them in the tables attached to the
programming devices;
- customization of identifying texts for
user positions and entry panels.
CONFIGURATION OF THE SYSTEM
WITH PROGRAMMING IN BASIC
MODE AND DEFAULT SETTINGS
Maximum limits of the system
- Maximum number of XA/301LR: 1.
- Maximum number of blocks X2-X1:
64.
- Maximum number of entry panels per
block X2-X1: 4.
- Maximum number of entry panels
300: 20 (19 with IPD/300LR).
- Maximum number of porter switch-
boards IPD/300LR: 1.
- Maximum number of users connected
directly to XA/301LR: 100 (0 if present
blocks X2-X1).
- Maximum number of users on block
X2-X1: 100 (99 with porter switch-
board IPD/300LR with encoded entry
panel HAC/300).
- Maximum number of relay actuators
IOD/303LR: 1.
Default settings
• System activation time:
call 30 s, conversation 60 s maximum.
• Door-lock release activation time:
- for entry panel 300 (with ICP/LR) with
selectable buttons from 1 s, 4 s, 8 s
and 16 s;
- for entry panel HAC/300LR adjustable
from 1 s to 255 s;
- for entry panel X2-X1 adjustable from
1 s to 15 s;
• Aux 1 command and door lock
release active only when internal
extension is called.
• Self-connection and scanning only
on block entry panels X2-X1.
• Automatic assignment of first key
of all entry panels 300 and X2-X1 as
porter call.
m
ATTENTION
The SERVICE button for program-
ming the unit is located near the
terminals. Be especially careful with
the terminals (~ ~) shown in figure 1
by the letter A, as voltage is present.
Basic programming
Programming structures the system
through the assignment of an identi-
fication code unique to all LON devices
(e.g. ICP/LR, HAC/300LR, IPD/300LR) and
X2-X1 (e.g. internal extensions and block
entry panels X2-X1 such as HEV/301,
HEC/301, etc.).
Programming is divided into two parts:
- programming of entry panels and
accessories.
- programming of internal extensions.
Accessing and exiting basic pro-
gramming
To access programming, you must press
the SERVICE button.
Programming is accessed by the
sequence described below.
6
Access to programming of entry panels.
The yellow LED is off
1 - Press the SERVICE button for at least
3 s, the yellow LED flashes steadily.
2 - Press the SERVICE button again for
at least 3 s, the yellow LED stays on.
3 - To exit programming, press the serv-
ice button for about 1 s, the yellow
LED goes off.
Access to programming of internal
extensions.
The yellow LED is off
1 - Press the SERVICE button for at least
3 s, the yellow LED flashes at a steady
rate.
2 - To exit programming, press the serv-
ice button for about 1 s, the yellow
LED goes off.
NOTE:
When you exit programming mode by
pressing the SERVICE button for 1 s, this
starts automatic programming of any
IPD/300LR and IOD/300LR.
PROGRAMMING
Power up the XA/301LR power supplier
and proceed as follows.
1 - PROGRAMMING OF ENTRY
PANELS 300, BLOCK ENTRY
PANELS X2-X1 MASTER
Programming, in addition to establish-
ing the order of scanning of the entry
panels, allows you to set the type of
entry panel 300 (audio or video entry
control), the duration of the command
for opening of the solenoid lock (only
for 300 plates with buttons) and the
definition of the number of X2-X1 but-
tons in the system.
1.1 - Access programming of entry
panels (yellow LED on).
300 entry panels
(ICP/LR or HAC/300LR) (fig. 7)
In entry panels with button (ICP/LR) the
busy signal light comes on (if present),
while in digital entry panels (HAC/300LR)
the message CONFIGURATION MODE
appears.
1.2 - Programming of entry panel and
door lock release time.
• Programming of video entry panel
ICP/LR and door lock release time1 s.
- Press call button no. 1.
Wait for two acoustic confirmation notes.
• Programming of audio entry panel
ICP/LR and door lock release time1 s.
- Press call button no. 1.
Wait for two acoustic confirmation notes.
- Again press call button no. 1.
Wait for an acoustic confirmation note.
• Programming of video entry panel
HAC/300LR and door lock release
time1 s.
- Type in the first code followed by .
Wait for two acoustic confirmation notes.
• Programming of audio entry panel
HAC/300LR and door lock release
time1 s.
- Type in the first code followed by .
Wait for two acoustic confirmation notes.
- Again type in the first code followed by .
Wait for an acoustic confirmation note.
1.3 - Repeat the procedure from point
1.2 on the next entry panels (in the
desired order of scanning of the entry
panels).
When the procedure is complete, the busy
light goes off or the CONFIGURATION
MODE message disappears to indicate
that programming is complete.
NOTE.
• If you want to modify the activation
time of the door lock release in IPC/LR
from 1 s to 4 s, 8 s or 16 s, perform the
steps in point1.2 or 1.3 using respectively
call button no. 2, 3, 4.
• On HAC/300LR plates, the time can be
programmed directly from the entry
panel referring to the manual.
Block entry panels X2-X1 Master
(HEV/301, HEC/301, AZV/304, etc.)
(fig. 7)
ATTENTION. Programming of block entry
panels X2-X1 will be possible only with
units that are version 3.0 or later.
1.4 - For the definition of each block
entry panel X2-X1 Master, the two
sequential steps listed below are
required.
A - Identification
block entry panel
• R emove and re-connect jumper
SW2 of the first entry panel (Master)
connected to the power supplier
XA/301LR, (fig. 7) of the first block
X2-X1 and wait for confirmation.
Confirmation is signalled by a double
acoustic signal with activation of the sole-
noid lock command.
B - Definition of number of calls
users of the block
This programming is to be carried out
only from the Master entry panel as
follows:
• Definition of the number of buttons
used in the audio/video entry panel
(0, 1, 2, 3 or 4):
- press the last button used on the
audio/video entry panel (fig. 8-A);
- press button 1 (brown, black wiring)
if you intend to use a call button.
Press button 2 (red, black wiring) if
you intend to use two call buttons.
Proceed in the same way to define the
other call buttons.
- If no call buttons are connected, press
the first button of the additional entry
panel (fig. 8-B).
• Definition of total number of users
connected on block X1, X2:
- Press the first button used on the
audio/video entry panel (IF USED), or
the first button on the additional entry
panel HEP/306 and the last button
used on the audio/video entry panel
(or additional panel).
A
B
1-M
2-R
3-C
4-G
1-M
2-R
3-C
4-G
N
1.5 - Repeat the procedure in point 2.4
for the subsequent Master entry panels
of the other blocks.
Programming of Slave entry panels of
the same block (fig. 7) must be done
afterwards (see paragraph "Program-
ming X2-X1 Slave entry panels").
1.6 - Exit programming.
Examples of definition
number of user calls
EXAMPLE 1 - Block X2-X1 with Targha
audio entry panel with 3 calls, without
additional button panels (fig. 9).
1A
1 -
Press call button no. 3 (position
1A) to define the number of buttons
used (3) in the audio/video panel.
Wait for the confirmation note (*).
2 -
Press the same button again to
define the total number of user calls for
the block (3).
Wait for the confirmation note (*).
EXAMPLE 2 - Block X2-X1 with Targha
audio entry panel with 10 calls and
additional button panels (fig. 10).
1B
1 -
Press call button no. 4 (position 1B)
to define the number of buttons used
(4) in the audio/video panel.
Wait for the confirmation note (*).
2 -
Then press call button no. 10 (posi-
tion 2B) to define the total number of
user calls for the block (10).
Wait for the confirmation note (*).
EXAMPLE 3 - Block X2-X1 with Targha
video entry panel with 12 calls and
additional button panels (fig. 11).
1C
1 -
Press call button no. 1 (position
1C) to define the number of buttons
used (0) in the audio/video panel.
8
Wait for the confirmation note (*).
9
2B
10
2C
11
Publicité
