Krups Prep&Cook XL HP50A8 Mode D'emploi page 48

PROBLEMS CAUSES
The appliance is not positioned
on a flat surface, the appliance is
not stable.
Excessive vibration.
Volume of ingredients too high.
Accessory error.
The spindle of your appliance
may create a noise during
Slight noise during
operation at reduced speed
operation
or with the use of certain
ingredients (rice...)
Excessive noise during
The use of a wrong accessory
operation
Volume of ingredients too high.
The lid is not correctly positioned
or locked.
Leak through lid. The lid seal is not present.
The lid seal is cut or damaged.
Accessory error.
The bowl seal (D4) is not
correctly positioned.
Leak from the driver in
The bowl seal is damaged.
the bowl
The locking ring (D5) is not
locked correctly.
The blades do not Pieces of food that are too big or
rotate easily. too hard.
On using the appliance for the
first time, or in the event of
overload of the motor caused
Smell from motor.
by too large a quantity of
ingredients or by pieces that are
too hard or too big.
The appliance has detected
"STOP" is displayed. too many vibrations and has
changed to the safety mode.
Motor overload caused by too
many ingredients or pieces
"SECU" is displayed. which are too hard or too large
or overuse without sufficient
cooling down time.
94
SOLUTIONS
Place the appliance on a flat surface.
Reduce the quantity of ingredients
processed.
Check that you are using the
recommended accessory.
This is a temporary phenomenon, which
has no consequences on the life of your
appliance. It will fade or disappear after a
few uses and cleaning operations of the
removable spindle (refer to the paragraph
"Cleaning the appliance").
Please use an adequate accessory (e.g.:
do not use the beater F3 for kneading or
mixing the dough, use the knife F4). For
this, refer to the recommendations in the
recipes and the operating instructions
provided in this manual.
Reduce the quantity of ingredients
processed.
Lock the lid correctly on the bowl.
Position the seal on the seal holder and
clip the assembly to the lid.
Change the seal, contact an approved
service centre.
Check that you are using the
recommended accessory.
Position the seal correctly.
Contact an approved service centre.
Screw the ring in place (D5).
Reduce the size or quantity of the
ingredients processed. Add some liquid.
Allow the motor to cool down (about
30 minutes) and reduce the number of
ingredients in the bowl.
Check that you are at the right speed
and that you are using the recommended
accessory.
Allow the motor to cool down (about
30 minutes) and reduce the number of
ingredients in the bowl.
PROBLEMS CAUSES
"SECU" is displayed
Overheating of temperature
+ red indicator light is
sensors.
flashing.
"Err1" is displayed.
The heating element is not
+ red indicator light is
working.
flashing.
"Err2" is displayed. Electronic fault.
"Err3" is displayed. Speed fault.
Communication fault with
"Err4" is displayed.
chopper electronic card.
Display "Err8" Safety locking sensor fault
"ntc1" is displayed. Temperature sensor 1 is no
longer working.
"ntc2" is displayed. +
Temperature sensor 2 is no
red indicator light is
longer working.
flashing.
Improper locking of the bowl
or lid
Safety indicator
display (C5)
The lid is locked on the bowl in
the "cooking without a lid" mode
The appliance was turned off
The safety lock on the
as a recipe was in progress
lid remained active
by toggling the I/O switch to
(rod extended) and
the "O" position or was simply
prevents the lid from
unplugged as a recipe was in
locking.
progress.
Is your appliance still not working?
Contact an approved service centre (see list in service booklet).
RECYCLING
„ Elimination of packaging and appliance materials.
The packaging exclusively contains materials that are not dangerous to the envi-
ronment, which can be disposed of in accordance with the recycling regulations
in force.
To dispose of your appliance, ask the appropriate department of your local authority.
„ End-of-life electronic or electrical appliances:
Environmental protection first!
Your appliance contains numerous materials that can be recovered or recycled.
Take it to a collection point for processing.
SOLUTIONS
Contact an approved service centre.
Check that the power pins under the
bowl are not clogged. If this is the case,
clean them and try again.
If that still does not work, contact an
approved service centre.
Contact an approved service centre.
Contact an approved service centre.
Contact an approved service centre.
Contact an Approved Service Centre.
Contact an approved service centre.
Contact an approved service centre.
Prior to operating the appliance, check
that the bowl is properly locked on the
motor unit and that the lid is properly
locked on the bowl. If the problem
persists, contact an authorised centre.
Unlock the lid prior to launching the
cooking program. If the problem persists,
contact an authorised centre.
Simply toggle the I/O switch to the "I"
position to reset the food processor,
along with the safety lock on the lid; the
rod will automatically return to its original
position. You may now lock the lid.
95