Motion Detecting Control Panel Models Cmxeocg772 And Cmxeocg982; Motion Sensor - Craftsman CMXEOCG322 Manuel Du Propriétaire

MOTION DETECTING CONTROL PANEL
MODELS CMXEOCG772 AND CMXEOCG982
SYNCHRONIZE THE DOOR CONTROL: To synchronize the door control to the garage door
opener, press the push bar until the garage door opener activates (it may take up to 3
presses). Test the door control by pressing the push bar; each press of the push bar
will activate the garage door opener.
Push Bar
1, 5, and
10 Minute
HOLD OPEN
TTC LED
Button(TTC)
LIGHT Button

Motion Sensor

PUSH BAR: Press the push bar to open or close the door.
LIGHT BUTTON: Press the LIGHT button to turn the garage door opener lights on or off.
When the lights are turned on they will stay on until the LIGHT button is pressed
again, or until the garage door opener is activated. Once the garage door opener is
activated the lights will turn off after the specified period of time (the factory default
is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in
motion. The Light Feature will turn on the light on the garage door opener when
someone enters through the open garage door and the safety reversing sensor infrared
beam is obstructed.
To change the amount of time the lights stay on:
Press and hold the LOCK button (approximately 10 seconds) until the garage door
opener lights flash. The time interval is indicated by the number of times the garage
door opener lights flash:
• 1 flash is 1-1/2 minutes
• 2 flashes is 2-1/2 minutes
• 3 flashes is 3-1/2 minutes
• 4 flashes is 4-1/2 minutes
To cycle through the time intervals repeat the step above. If the push bar LED is
continuously blinking, the LOCK feature needs to be turned off.
To turn the Light feature on or off (Factory default is On):
Turn OFF:
1. Close the garage door.
2. Start with the garage door opener lights "OFF".
3. Press and hold the LIGHT button (approximately 10 seconds) until the garage
door opener lights turn off, then on again.
Turn ON:
1. Close the garage door.
2. Start with the garage door opener lights "ON".
3. Press and hold the LIGHT button (approximately 10 seconds) until the garage
door opener lights turn off, then on again.
Motion Sensor Switch
Command LED
LEARN Button
LOCK Button
LEARN BUTTON: Any compatible remote control, wireless keypad, or myQ
can be programmed to the garage door using the LEARN button.
MOTION SENSOR: The motion sensor automatically turns on the garage door opener
lights when motion is detected. The lights come on for the set period of time, and
then shut off. If using the garage door opener light as a work light disable the motion
sensor, otherwise the lights may turn off automatically if you are beyond the range of
the motion sensor.
ON (TTC)
The motion sensor switch turns the motion sensor on or off.
OFF (TTC)
LOCK: Prevents the garage door opener from being activated by remote controls while
still allowing activation from the door control and wireless keypad.
Turn ON:
Press and hold the LOCK button for 2 seconds. The command LED will flash as long
as the lock feature is on.
Turn OFF:
Press and hold the LOCK button for 2 seconds. The command LED will stop flashing
and normal operation will resume.
TIMER-TO-CLOSE (TTC) (Factory default is set to off): The Timer-to-Close feature
automatically closes the door after a specified time period and can be adjusted using
the door control. DO NOT enable TTC if operating a one-piece door. TTC is to be used
ONLY with sectional doors. The garage door opener will beep and the lights will flash
before closing the door. The TTC feature will deactivate if the garage door encounters
an obstruction twice; or the safety reversing sensors are incorrectly installed. The
garage door will reverse open and WILL NOT close until the obstructions are clear or
the safety reversing sensors are correctly installed. When the obstruction has been
cleared or the safety reversing sensors have been aligned, the door will close when
the garage door opener is activated. TTC WILL NOT work if the garage door opener is
operating by battery power or if the safety reversing sensors are misaligned. This
feature is NOT intended to be the primary method of closing the door. A wireless
keypad should be installed in the event of an accidental lock out when using this
feature.
To turn TTC on or off or to set the TTC time interval:
Turn ON:
1. Press and hold the ON button until one of the TTC LEDs light up.
2. Then press the ON button again to cycle through the time interval options.
The TTC time interval can be set to 1, 5, and 10 minutes (the corresponding
TTC LED will light for each time interval). The garage door opener light bulbs
will blink as confirmation. Once the TTC has been set and the door is open,
the TTC LED for the selected time interval will blink and begin to count
down to close the door.
Turn OFF:
1. Press and hold the OFF button until all TTC LEDs turn off and a beep is heard
from the garage door opener.
Temporarily hold door open (suspend TTC):
1. Press and release the HOLD OPEN button.
2. Press the HOLD OPEN button again to resume normal TTC operation.
36
® devices