Dual-Function Control Panel Model Cmxeocg572; Light Button; Door Control Model Cmxeocg322 - Craftsman CMXEOCG322 Manuel Du Propriétaire

DUAL-FUNCTION CONTROL PANEL
MODEL CMXEOCG572
SYNCHRONIZE THE DOOR CONTROL: To synchronize the door control to the garage door
opener, press the push bar until the garage door opener activates (it may take up to 3
presses). Test the door control by pressing the push bar; each press of the push bar
will activate the garage door opener.
Push Bar

LIGHT Button

PUSH BAR: Press the push bar to open or close the door.
LIGHT BUTTON: Press the LIGHT button to turn the garage door opener lights on or off.
When the lights are turned on they will stay on until the LIGHT button is pressed
again, or until the garage door opener is activated. Once the garage door opener is
activated the lights will turn off after the specified period of time (the factory default
is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in
motion. The Light Feature will turn on the light on the garage door opener when
someone enters through the open garage door and the safety reversing sensor infrared
beam is obstructed.
To change the amount of time the lights stay on:
Press and hold the LOCK button (approximately 10 seconds) until the garage door
opener lights flash. The time interval is indicated by the number of times the garage
door opener lights flash:
• 1 flash is 1-1/2 minutes
• 2 flashes is 2-1/2 minutes
• 3 flashes is 3-1/2 minutes
• 4 flashes is 4-1/2 minutes
To cycle through the time intervals repeat the step above. If the push bar LED is
continuously blinking, the LOCK feature needs to be turned off.
To turn the Light feature on or off (Factory default is On):
Turn OFF:
1. Close the garage door.
2. Start with the garage door opener lights "OFF".
3. Press and hold the LIGHT button (approximately 10 seconds) until the garage
door opener lights turn off, then on again.
Turn ON:
1. Close the garage door.
2. Start with the garage door opener lights "ON".
3. Press and hold the LIGHT button (approximately 10 seconds) until the garage
door opener lights turn off, then on again.
Command LED
LEARN Button
LOCK Button
LEARN BUTTON: Any compatible remote control, wireless keypad, or myQ
can be programmed to the garage door using the LEARN button.
LOCK: Prevents the garage door opener from being activated by remote controls while
still allowing activation from the door control and wireless keypad.
Turn ON:
Press and hold the LOCK button for 2 seconds. The command LED will flash as long
as the lock feature is on.
Turn OFF:
Press and hold the LOCK button for 2 seconds. The command LED will stop flashing
and normal operation will resume.
TIMER-TO-CLOSE (DO NOT enable on one-piece doors)
The Timer-to-Close feature is not available on all door controls. Below is a list of
door controls with the Timer-to-Close feature:
The Timer-to-Close feature automatically closes the garage door after a specified
time period. DO NOT enable TTC if operating a one-piece door. TTC is to be used
ONLY with sectional doors. Factory default is set to off. The garage door opener will
beep and the lights will flash before closing the door. The TTC feature will deactivate
if the garage door encounters an obstruction twice; or the safety reversing sensors are
incorrectly installed. The garage door will reverse open and WILL NOT close until the
obstructions are clear or the safety reversing sensors are correctly installed. When the
obstruction has been cleared or the safety reversing sensors have been aligned, the
door will close when the garage door opener is activated. TTC WILL NOT work if the
garage door opener is operating by battery power or if the safety reversing sensors are
misaligned. This feature is NOT intended to be the primary method of closing the
door. A wireless keypad should be installed in the event of an accidental lock out
when using this feature.
DOOR CONTROL
MODEL CMXEOCG322
SYNCHRONIZE THE DOOR CONTROL: To synchronize the door control to the garage door
opener, press the push button until the garage door opener activates (it may take up to
3 presses).
Push Button
35
®
devices