Fixture Setting; Lamp Setting - Briteq BTX 5R BEAM Mode D'emploi

ENGLISH OPERATION MANUAL

Fixture Setting

Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and DOWN buttons to
select Pan Inverse, Tile Inverse, BL.O. P/T Moving, BL.O. Color Change or BL.O. Gobo Change.
Pan Inverse
Select Pan Inverse, press ENTER button to confirm, current mode will blink on the display, use UP and
DOWN buttons to select No (normal) or Yes (pan inverse), press ENTER button to store. Press the MENU
button to go back to the last menu, if you leave the unit unused for one minute it will automatically exit from
menu mode.
Tilt Inverse
Select Tilt Inverse, press ENTER button to confirm, current mode will blink on the display, use UP and
DOWN buttons to select No (normal) or Yes (tilt inverse), press ENTER button to store. Press the MENU
button to go back to the last menu, if you leave the unit unused for one minute it will automatically exit from
menu mode.
P/T Feedback (pan/tilt Feedback)
Select P/T Feedback, press ENTER button to confirm, current mode will blink on the display, press
UP/DOWN buttons to select No (Pan or tilt's position will not feedback while they are out of step.) or Yes
(pan/tilt will feedback if they are out of step.), press ENTER button to store. Press the MENU button to go
back to the last menu, if you leave the unit unused for one minute it will automatically exit from menu mode.
BL.O. P/T Moving (Blackout while pan/tilt moving)
Select BL.O. P/T Moving, Press ENTER button to confirm, current mode will blink on the display, use UP
and DOWN buttons to select No (normal while pan/tilt are moving) or Yes (blackout while pan/tilt are
moving), press ENTER button to store. Press the MENU button to go back to the last menu, if you leave the
unit unused for one minute it will automatically exit from menu mode.
BL.O. Color Change (Blackout while change color)
Select BL.O. Color Change, press ENTER button to confirm, current mode will blink on the display, use UP
and DOWN buttons to select No (normal while the color is changing) or Yes (blackout while the color is
changing), press ENTER button to store. Press the MENU button to go back to the last menu, if you leave
the unit unused for one minute it will automatically exit from menu mode.
BL.O. Gobo Change (Blackout while change gobo)
Select BL.O. Gobo Change, press ENTER button to confirm, current mode will blink on the display, use UP
and DOWN buttons to select No (normal while gobo is changing) or Yes (blackout while gobo is changing),
press ENTER button to store. Press the MENU button to go back to the last menu, if you leave the unit
unused for one minute it will automatically exit from menu mode.

Lamp Setting

Enter menu mode, select Lamp Setting, press ENTER button to confirm, use UP and DOWN buttons to
select On/Off, State/Power on, Off Via DMX, On if DMX on, Off if DMX off, Cooling Mode, Ignition Delay
or Low Power Delay
On/Off (Turn on/off the lamp)
Select On/Off, press ENTER button to confirm, current mode will blink on the display, use UP and DOWN
buttons to select On (lamp on) or Off (lamp off), press ENTER button to store. Press the MENU button to go
back to the last menu, if you leave the unit unused for one minute it will automatically exit from menu mode.
State/Power On (Lamp state while power on)
Select State/Power On, press ENTER button to confirm, current mode will blink on the display, use UP and
DOWN buttons to select On (Lamp strike during the startup reset) or Off (Lamp is off at the startup), press
ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu
mode.
Off Via DMX (Turn off the unit via DMX controller)
Select Off Via DMX, press ENTER button to confirm, current mode will blink on the display, use UP and
DOWN buttons to select Yes (enable turn off lamp via DMX) or No (disable turn off lamp via DMX), press
BRITEQ 9/95 BTX-BEAM 5R
®