Cata IB 6103 BK Instructions Pour L'usage Et La Maintenance page 20

on the installed equipment.
This appliance is not intended to be used
via an external timer or a remote control
system.
The manufacturers
responsibility in the event of non-
compliance with what is described above
and the accident prevention norms not
being respected and followed.
To avoid all risk, if the power cable
becomes damaged, it must only be
replaced by the manufacturer, by an
authorised service centre, or by a
qualified electrician.
OPERATING PRINCIPLE (Fig. 1)
It exploits the electromagnetic properties of most cooking
vessels.
The coil (inductor) which produces the electromagnetic field is
operated and controlled by the electronic circuit.
The heat is transmitted to food by the cooking vessel itself.
The cooking process takes place as described below.
- loss of heat is minimum (high efficiency)
- the system stops automatically when the vessel is removed or
even just lifted from the hob
- the electronic circuit guarantees maximum flexibility and fine
adjustments.
(Fig. 1)
1 Vessel
2 Induced current
3 Magnetic field
4 Inductor
5 Electronic circuit
6 Power supply
User's Instructions (Fig. 2)
1 ON / OFF
2 Minus -
3 Plus +
4 Cooking zone indicator / Zone to temporize selector
5 Power level display / Temporized zone Display / Timer Display
6 Lock
7 Lock indicator
Installation
All operations relative to installation (electric connection) should
be carried out by skilled personnel in conformity with the rules
in force.
decline any
As for the specific instructions see part pertaining to installer.
Switching the Touch Control ON/OFF "Z"
After mains voltage is applied the control initializes for approx. 1
second before it is ready for operation.
After a reset all displays and LEDs glow for approx. 1 second.
When this time is over all displays and LEDs extinguish and the
control is in the stand-by mode. Safety lock is activated and the
safety lock indicator LED is illuminated (7).
Before turning on the hob and operating the controls, press the
safety lock button (6) for two seconds to unlock the keypad for
normal operation.
Press the ON/OFF (1) button to switch the touch control on.
The cooking zone displays show a static ".".
If a cooking zone is in the "hot" status, the display shows a static
"H" instead of "0".
After switching-ON the electronic control remains activated for
10 seconds. If no cooking zone or timer selection follows within
this period of time, the electronic control automatically switches
back into the stand-by-mode. The control can only be switched-
ON if it identifies the ON/OFF (1) key alone being operated.
Should it recognize ON/OFF (1) key activation other than that,
the control remains in the standby- mode.
If the child safety feature is active when switching on, the Safety
lock indicator (7) lights up. When the Touch Control is ON it can
be switched- OFF at any time by operating the ON/OFF (1) key.
This is also valid if the control has been locked (activated child
safety feature).
The ON/OFF (1) key has always priority in the switch-OFF
function.
Automatic switch-OFF
When the control is ON it automatically switches-OFF after 10
seconds if no cooking zone or select key has been operated
within this period of time. If no pan is placed on a cooking zone
after selecting a power level for that area on the hob, it will
automatically turn off after 1 minute.
Switching a cooking zone ON and OFF
First place the pan in the chosen cooking zone. If the pan is not
present the system cannot be switched on the correspondent
zone.
When the touch control is on, a cooking zone may be selected
by pressing the (4) buttons on the corresponding area.
The display (5) for the chosen cooking zone will show the
selected power level.
If the cooking zone is "hot", "H" are alternately displayed.
Press the PLUS (3) or MINUS (2) button to select a setting and
the zone will begin to heat up.
Once the cooking zone has been selected, the setting can be
selected by keeping the PLUS (3) button pressed down. The
setting begins at level 1 and increases by 1 level every 0.4
seconds. When setting "9/P" is reached, the setting will not be
changed further.
If the setting level has been selected using the MINUS (2) button,
the start level is "9" (maximum level). Keep the button pressed
down to lower the active level by 1 every 0.4 seconds. When