Cata IB 6103 BK Instructions Pour L'usage Et La Maintenance page 22

If no cooking zone is selected for the timer function within 5
seconds, the timer function will be automatically deactivated.
After selecting the cooking zone to be timed, the time must be
selected within 5 seconds; otherwise, the timer function will be
automatically deactivated.
The selected time will start 5 seconds after setting the timer. The
timer setting can be modified during timer cycle by pressing
the buttons UP TIMER (9) or DOWN TIMER (8). The new timer
setting will start 5 seconds after programming the new timer
setting.
To deactivate the timer function at any time press simultaneously
the UP TIMER (9) and DOWN TIMER (8). Pressing the DOWN
TIMER (8) button until the timer display (7) shows "00" also
deactivates the timer function.
When the set time has elapsed, the selected cooking zone will
switch off and the timed zone indicator (6) and time indicator
(7) LEDs will illuminate intermittently while a warning beep will
sound for 1 minute. To cancel this acoustic warning before the
set time has elapsed, press any button on the touch control.
Cooking vessels (Fig. 3)
- a magnet-attracting vessel may be a suitable vessel for
induction cooking
- prefer vessels which are especially declared to be suitable for
induction cooking
- flat- and thickbottomed vessels
- a vessel with the same diameter as zones ensures the maximum
exploitation of power
- a smaller vessel reduces power exploitation, but does not cause
any energy loss We would anyhow not recommend the use of
vessels with diameters smaller than 10 cm.
- stainless-steel vessels with multi-layer or ferritic stainless-steel
bottoms when specifically suited for induction cooking
- cast-iron preferably enamel-bottomed vessels to avoid
scratching the pyroceram surface
- we do not recommend the use of any glass, ceramic,
earthenware, alluminium, copper or non-magnetic (austenitic)
stainlesssteel vessels.
Maintenance (Fig. 4)
Any remains of aluminium foil, food, fat, sugar or food with
high sugar content must be immediately removed from the hob
surface with a scraper to prevent potential damage to the hob
surface.
Subsequently clean the surface with some towel and appropriate
product, rinse with water and dry by means of a clean cloth.
Under no circumstance should sponges or abrasive cloths be
used; also avoid using aggressive chemical detergents such as
oven sprays and spot removers.
Installer's Instructions
Installation
These Instructions are for the qualified technician, as a guide to
installation, adjustment and maintenance, according to the laws
and standards in force. These operations must always be carried
out when the appliance has been disconnected from the electric
system.
Positioning (Fig. 5)
The fixture is especially designed for fitting into a work-top as
shown in the corresponding figure.
Place the supplied sealing agent along the hob perimeter.
Do not install the hob over an oven; in case you do, make sure
of the following:
- the oven is equipped with an appropriate cooling system
- there is no warm-air leakage from the oven towards the hob
- suitable air-inlets are provided as shown in the figure.
Electrical connection (Fig. 6)
Prior to carrying out the electrical connection, please ensure
that:
- the plant characteristics are such as to follow what is indicated
on the matrix plate placed at the bottom of the working area;
- that the plant is fitted with an efficient earth connection,
following the standards and law provisions in force.
The earth connection is compulsory in terms of the law.
Should there be no cable and/or plug on the equipment, use
suitable absorption material for the working temperature as
well, as indicated on the matrix plate. Under no circumstance
must the cable reach a temperature above 50°C of the ambient
temperature.
Power limitation function (only on certain models)
The appliance features a function that allows the maximum
power level to be limited internally. This maximum power level
limit can be selected from the following power values: 7,200 W,
6,000 W, 3,500 W and 2,800 W. The appliance is configured by
default to the maximum power level limit.
To modify this factory setting, after connecting the appliance
to the power supply, with the touch control unlocked and all
cooking zones inactive, press simultaneously the UP (3) and
DOWN (2) buttons at the two ends of the touch control within 30
seconds of connecting the power supply. The display will show
the power level selected. Use the UP (3) or DOWN (2) buttons
on any cooking zone to select one of the available values. Once
the desired value is selected, press simultaneously the UP (3)
and DOWN (2) buttons at the two ends of the touch control to
memorise the power level limit and turn off the touch control.
If when using the appliance a power level is selected that exceeds
the limit, the affected cooking zone display will show the symbol
"r" for 3 seconds and return to the previous power level.
To increase the power level on a given cooking zone, it may be
necessary to reduce the level on another cooking zone in order
to remain within the overall power limit.