Safety Notes; Applications - Monacor TXA-1022CD Mode D'emploi

– insertion "MEMORY" for replaying a
programmed track sequence
– insertion "A © B" when replaying a
loop
25 Slot for an SD card
26 Button to select CD, USB storage
device or SD card
27 Button FOLDER to select the next
folder (for MP3 mode)
28 Button F.F/ for fast forward and
button FB/ for fast reverse:
Shortly press the respective button
and when the desired spot is reached,
press the replay/ pause button (30).
29 Buttons for track selection
REV/ S
= reverse,
S = forward
F.WD/
30 Replay/ pause button
31 Button to change to the stop mode
(button is pressed for the first time) and
to eject a CD (button is pressed for the
second time)
32 Buttons to change the playing speed
in 10 steps:
Press the button HI / HIGH (to increase
speed) or LO / LOW (to de crease speed)
repeatedly until the de sired speed is
reached; to return to standard speed,
press the button NOR.
33 Volume control
34 Numerical keys for track selection by
entering its number (MP3 mode: num-
ber of the track on the playing medium,
not in the folder!); after the input, press
the button ENTER (40) to confirm
35 Button to program an individual track
sequence chapter 7.3.11
36 Button for track replay in a random
order
37 Button to select
– "REPEAT 1": repeat of the track
– "REPEAT FOLDER" (for MP3 mode
only): repeat of all tracks in the folder
– "REPEAT ALL": repeat of all tracks
of the playing medium
– No "REPEAT" insertion: no repeat
function activated
38 Button to stop the replay
39 Button to replay a loop
(repeat of a section in the track)
button is pressed for the first time
to define the starting point of the sec-
tion
button is pressed for the second time
to define the end point of the section:
replay of the loop will start.
Button is pressed for the third time
to terminate the replay of the loop
40 Button to confirm an input, e. g. after
track selection via the numerical keys
(34)
41 Button to activate / deactivate the sound
Transmitting module AUDIO LINK TX
Wireless audio link mode: Via the transmit-
ting module of an active speaker system
TXA-1022CD (master unit), its output sig-
nal can be transferred to the receiving mod-
ules of other active speaker systems (slave
units) of the series TXA-800 / -1000 / -1020.
At the receiving modules of the slave units,
set the transmission channel and set the
transmitting module of the master unit to
the same channel. Please note: At the
master unit, the receiving module and the
transmitting module must be set to different
channels; otherwise, there will be feed-
back.
Note: The tone controls (6) and the control MAS-
TER (11) at the master unit will not have any
effect on the output signal of the transmitting
module.
42 Display to indicate the transmission
channel (CH 1 ... CH 16)
43 Transmission indicator; will light up
when the transmitting module is
switched on
44 Level indicators for the audio signal at
the input of the transmitting module:
yellow LED: will light up when a spe-
cific minimum level has been reached
red LED: overload indicator, should
only light up briefly for signal peaks;
if it lights up continuously, reduce
the volume of the respective audio
source(s)
45 Buttons for setting the transmission
channel:
1. Press the button SET: The channel
indication on the display will start
flashing.
2. As long as the channel indication
flashes (10 sec.), the arrow buttons
can be used to select the channel.
3. Confirm the selected channel with
the button SET (otherwise, the
transmitting module will return to
the previously set channel after
10 seconds).
To briefly indicate the radio frequency
during operation, keep one of the
arrow buttons pressed: The display
will indicate the frequency instead of
the channel while the arrow button is
pressed.
46 Power switch and volume control of
the transmitting module

2 Safety Notes

The unit (incl. remote control) corresponds
to all relevant directives of the EU and is
therefore marked with .
WARNING The unit uses dangerous
mains voltage. Leave servic-
ing to skilled personnel. Inex-
pert handling may result in
electric shock.
G
The unit is suitable for indoor use only.
Protect it against dripping water and
splash water, high air humidity, and heat
(admissible ambient temperature range
0 – 40 °C).
G
Do not place any vessel filled with liquid
on the unit, e. g. a drinking glass.
G
Do not operate the unit and immediately
disconnect the mains plug from the socket
1. if the unit or the mains cable is visibly
damaged,
2. if a defect might have occurred after
the unit was dropped or suffered a
similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by
skilled personnel.
G
Never pull the mains cable to disconnect
the mains plug from the socket; always
seize the plug.
G
For cleaning only use a dry, soft cloth;
never use water or chemicals.
G
No guarantee claims for the unit and no
liability for any resulting personal dam-
age or material damage will be accepted
if the unit is used for other purposes than
originally intended, if it is not correctly
connected or operated, or if it is not re -
paired in an expert way.
If the unit is to be put out of opera-
tion definitively, take it to a local
recycling plant for a disposal which
is not harmful to the environment.

3 Applications

This active speaker system TXA-1022CD
is a combination of a two-way speaker
system and a class D amplifier and is
especially designed for mains-independent
operation. For power supply, the unit is
equipped with two lead gel batteries that
are charged when the unit is connected to
the mains. Thus, the unit is ideally suited
for mobile PA applications, e. g. at events
and lectures.
The active speaker system is equipped
with controllable inputs for the connection
of two microphones and two audio sources
with line signal level (e. g. CD / MP3 player)
as well as with two outputs (e. g. for the
connection of another active speaker sys-
tem). Audio data of a Bluetooth audio
source (e. g. smartphone) can be repro-
duced via the integrated Bluetooth receiver.
11