Cleaning And Maintaining; Changing The Bag - Rowenta SILENCE FORCE EXTREME RO58 Serie Mode D'emploi

EN

CLEANING AND MAINTAINING

The air we breathe contains particles that may be allergens:
mite larvae and droppings, mould, pollen, smoke and animal
residues (hair, skin, saliva, urine). The smallest particles
penetrate deep into the respiratory system where they can
cause inflammation and lung impairment.(H)EPA filters (High
Efficiency Particulate Air) are used to filter out the smallest
particles. With the (H)EPA filter, the air released back into the
room is healthier than the air that is vacuumed.
IMPORTANT Always switch off and unplug your
vacuum cleaner before servicing it.
1 • Changing the bag
The change bag light tells you that the bag is full or
saturated. If you notice that your vacuum cleaner is not
working as well as it should be, turn the power up to
maximum and hold the lifted nozzle above the floor. If the
light stays red, replace the bag.
a) If your vacuum cleaner is fitted with a Wonderbag* (19a) :
IIMPORTANT Wonderbag* UNIVERSAL (Classic,
Freshline, Endura ref. WB4xxx) bags are available from
retail outlets and at Approved Service Centres.
IMPORTANT Wonderbag* COMPACT bags can't be
used on this appliance. Using them could damage
the vacuum cleaner and may invalidate the
appliance guarantee.
Open the cover to your vacuum cleaner (Fig.14).
Remove the bag support from the bag compartment (Fig.15a).
Remove the Wonderbag* bag from the bag support (Fig.15b).
Throw the Wonderbag* bag away (Fig.15c).
Place a new Wonderbag* bag in the bag support using its ring
(Fig.15d).
Place the bag support in the bag compartment and fit the bag
inside the compartment (Fig.15e).
Make sure that the bag is correctly positioned before closing
the cover.
b) If your vacuum cleaner is fitted with a High filtration bag*
(19b) :
The bags (ref. ZR002001) are available from your
retailer or from Approved Service Centres.
Open the cover of your vacuum cleaner (Fig. 14).
Remove the bag support from the bag compartment (fig.16a).
Before removing the dust bag from the bag support, pull the
tab on the card bag closure to seal the bag and avoid dust
escaping: grip the tab (Fig. 16b) and pull out fully to seal the
opening (Fig. 16c).
Detach the bag from the support (Fig. 16d).
Dispose of the bag in the waste bin (Fig. 16e).
Place a new bag in the bag support:
slide the card bag closure into the slots of the bag support
(fig.16f) until fully inserted (fig.16g) (the paper tab used to seal
the bag when full should be located underneath the bag
support).
* Depending on models: either equipment specific to cer-
tain models or available as an optional accessory.
Place the bag support into the bag compartment and spread
the bag out within the compartment (fig.16h).
Ensure that the bag support is correctly positioned before
closing the cover.
c) If your vacuum cleaner is fitted with a synthetic (textile)
bag* (19c) :
Synthetic bags* (ref.RS-RT2274) are available from
Approved Service Centres.
Open the cover to your vacuum cleaner (Fig.14).
Remove the bag support from the bag compartment (Fig.17a).
Remove the synthetic bag* from the bag support (Fig.17b).
Open the synthetic bag* using the zip (Fig.17c) then empty it
into a dustbin (Fig.17d).
Check that the zip is properly closed once more before putting
the bag back in again (Fig.17e).
Place the synthetic bag* on the bag support using its
cardboard holder (Fig.17f), place the bag support in the bag
compartment and fit the bag inside the compartment
(Fig.17g).
Make sure that the bag is correctly positioned before closing
the cover.
IMPORTANT Never operate the vacuum cleaner
without a bag.
For your peace of mind your vacuum cleaner is fitted
with a safety system which tells you that the bag is
inside (the cover won't close unless you've put the
bag in).
2 • Changing the (H)EPA* filter case
(ref. ZR002901)* (for the appliances
fitted with a Wonderbag vacuum bag
or a high filtration bag*)
IMPORTANT Replace the filtration system once a
year.
The (H)EPA filter cassette ref. ZR 0029 01* is available from
all retail outlets and at approved Service Centres.
Open the cover to your vacuum cleaner (Fig.14). Remove the
bag support from the bag compartment (Fig.15a or 16a),
then remove the (H)EPA* filter cassette (Fig.18a) and throw
the cassette into a bin (Fig.18b).
Fit the new (H)EPA* filter cassette (ref. ZR 0029 01*) into its
compartment (Fig.18c)
Put the bag support back into the compartment (Fig.15e or
16h).
Make sure that the (H)EPA* filter cassette is correctly
positioned before closing the cover.
10