Sygonix 43176Y Notice D'emploi page 3

Operating instructions
GB
Wireless color camera, IR
Intended use
The product is intended for surveillance by means of the integrated camera. It is oper-
ated by a wired 10/100MBit-Network (RJ45 jack). 7 IR LEDs are mounted under the
semi-transparent front panel.
The product must not get damp or wet, it is intended only for use in dry, indoor loca-
tions.
The power for the camera is supplied via the power transformer included in the de-
livery.
Please bear in mind that it is prohibited by law to watch strangers with a camera with-
out their knowledge and consent. Observe the rules and regulations of the country
where you are using the camera.
Any other use than that described above may damage the product. Moreover, this
may give rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the
product may be modifi ed or converted!
The safety instructions and technical data must be followed without fail!
This product complies with the applicable National and European requirements. All
names of companies and products are the trademarks of the respective owner. All
rights reserved.
Package Contents
• LAN Camera:
• Network cable
• Bracket with mounting material
• Wall plug transformer
• Mini-DVD with software and a comprehensive manual in English (PDF)
• Quick guide
Explanation of the Symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specifi c risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to
observe these safety instructions! We do not assume liability for any
consequential damage!
Nor do we assume liability for damage to property or personal injury
caused by improper use or failure to observe the safety instructions. The
warranty will be void in such cases.
• The unauthorised conversion and/or modifi cation of the product is not per-
mitted because of safety and approval reasons (CE). Never dismantle the
product.
• The product is not a toy and must be kept out of the reach of children. It
should be operated out of the reach of children.
• The use of the surveillance camera system does not replace the personal
supervision of children, or people who require special assistance, but only
serves as a support to this supervision.
• The design of the wall plug transformer complies with protection class II.
Only use a proper outlet of the public supply system as a voltage source for
the power supply.
• The product should only be used in dry indoor areas, it must not become
damp or wet! There is a risk of a lethal electric shock!
• The camera should not be exposed to extreme temperatures, direct sun-
light, strong vibrations or heavy mechanical stress.
The home technology brand for the entire house. More information at www.sygonix.com
• Make sure that the connection cable is not pinched or damaged by sharp
edges.
• Do not leave packaging material carelessly lying around since it could be-
come a dangerous plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or ac-
cidental drops, even from a low height.
• If the camera is used with other devices (e.g. a monitor), the operating in-
structions and safety notices for these devices must be followed as well.
• It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works
- the device has been stored under adverse conditions.
- it was exposed to heavy loads during transport
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operating
Materials are to be observed.
• Disconnect the power supply from the camera if it is not to be used for a
while (e.g. for storage).
• If you have any questions that are not answered in this manual, please con-
tact our technical service or another specialist.
Getting started, Connection via RJ45
• Connect the camera's RJ45 connector to a 1:1 connected network cable and its net-
work, e.g. a network switch.
• Connect the low-voltage socket of the camera to the corresponding round plug on
the enclosed power adapter. Insert the plug-in power adapter into a mains socket,
the "Power"-LED on the front of the camera lights up.
• Insert the CD provided in the appropriate drive of your computer. If the installation
software on the CD does not start automatically, you must start the installation pro-
gramme on the CD manually. At the time of writing this guide this could be found in
the main directory of the DVD (Program name "Autorun.exe").
Follow the program's instructions.
Be aware that the names and descriptions of the installation procedure, as de-
scribed here, may be changed in newer versions of the software. In this case please
observe the accompanying English language operating manual on the DVD (PDF).
• Start the newly installed software ("IP Discovery Tool"). It will search for available
cameras in the network. When the camera appears, with its corresponding IP ad-
dress, double click on it or select the camera and click "Connect".
Please note:
In your network a DHCP server must be active (e.g. the DHCP server of a router).
The PC must be confi gured so that it assigns an IP address automatically. The
camera is also assigned an IP address by the DHCP server.
If no DHCP server is present, the camera has the IP address 192.168.1.200 (net-
work mask 255.255.255.0). It is important that this IP address is not being
used by another device on the network. Otherwise, no access to the camera
is possible!
• When the camera asks for a username and password, enter "admin" for both (in
lowercase and without the quotation marks).
• We encourage you to use Internet Explorer as an Internet browser to be able to use
all the features of the camera. Before connecting to the camera an ActiveX plugin
must be installed.
Depending on the security settings for your Internet Explorer an error message ap-
pears, saying a required ActiveX element cannot be installed or that the installation
of the ActiveX can be started manually by clicking on the information bar.
This ActiveX element is necessary for the camera image to be shown.
• Furthermore, modifi cations to the settings of the antivirus or fi rewall programmes
may be required in order to have the softare working fl awlessly.