quadient IS-5000 Mode D'emploi page 2

IS-5000
• For more specific information about your
mailing system, see the User Guide.
kb.quadient.ca/is5000_ug_en
Applying postage
1
TO RESET PREVIOUS SETTINGS...
PRESS CLEAR OR WAKE
• If needed, press to get back
to the home screen.
• To get back to default rate settings,
press on the keyboard.
• If the system is asleep, press
to wake it up with default settings.
Thickness setting
There is a thin/thick mail latch under the top cover of the fee-
der. For normal operation, the lever will be to the left. However,
for processing a batch of thick mail, move the lever to the right,
especially if the thicker envelopes won't feed into the mail path.
1- Open the feeder
cover.
2- Change the lever
position:
- left for normal;
- right for thicker
mail
3- Close feeder
cover
• Touchscreen main areas
DO
D1
D2
D3
D4
2a
TO WEIGH YOUR MAIL...
USE THE DYNAMIC SCALE
• Tap the D2 area on the screen
and select
OR
2b
PUT YOUR MAIL ON THE SCALE
• Tap the D2 area on the screen
and select
Changing the ink tank
1- On the new ink tank, remove the protective
strips.
2- Open the ink tank drawer by pulling it towards
you.
3- Press on the blue release lever to disengage
the ink tank.
4- Pull out the old ink tank.
5- Insert the new ink tank,
then push it until you
hear the click.
6- Close the drawer. The
alignment process
of the printing heads
starts automatically.
Getting to know your mailing system
(tactile areas: )
DO • Rate and services
D5
D1 • Date printed
D6
D2 • Weighing type
D3 • Envelope sealing
D4 • Imprint position offset
D7
D5 • Type of imprint (to change: K5)
D6 • Postage and weight
D8
D7 • Job memories (can contain rate,
imprint settings and account)
D9
D8 • Current account
D9 • Ink level
3
CHOOSE RATE AND SERVICES
Current rate and selected
services are displayed in
this area of the screen.
To change the rate and/or add services:
1- Press .
The rate selection
screen is displayed.
2- Use rate buttons 1 to 9
to select an available
Class and/or Services,
or select Rate wizard.
Press OK to validate your selection and return
3-
to the home screen.
If jamming occurs...
In the base:
1- Pull the release handle on the lower
assembly of the print Base.
2- Using your other hand, remove the
jammed envelopes.
If the jammed envelopes can not be
removed, perform the following.
3- Press on the blue release lever to
disengage the lower conveyor.
In the feeder:
1- Open the cover.
2- Gently remove jammed
envelopes.
3- Close the cover.
K6
• Shortcut keys
K1
K7
K2
K8
K3
K4
K9
K5
4
IMPRINT PRINTING
If you want to print on a label or automatically seal the envelope, check additional
options below.
1- Press to start the motors of your Mailing
Machine.
2- Insert the mail piece in the feeder loader,
the imprint printing position on the upper right side.
To print on labels:
1- Insert labels into the dispenser until you hear a
click,
printing side facing the right.
2- Tap the D2 area on the screen and select
3- Press to enter the number of labels
To seal the envelopes:
Tap the D3 area on the screen to activate
deactivate the sealer.
Adding credit
Filling the sealer bottle
1- Remove the bottle
Press , type 2 and
from its base and
follow instructions on
screen. turn it over.
2- Unscrew the cap
Note: to complete this
and fill the bottle
operation successfully,
your postal services with water up to the
account must have a
limit marks.
positive credit balance
3- Screw on the cap
of the corresponding
and put the bottle
amount.
back into place.
K1 • Rate selection
K2 • Job memories
K3 • Print labels
K4 • Credit
K5 • Imprint configuration
K6 • ON/OFF Switch
K7 • Sleep / wake
K8 • Stops printing
K9 • Starts printing
.
or