Stack ST3513 Instructions D'installation page 2

A. Pre-existing 1/8" NPT Threaded hole
SET SCREW
1/8" NPT FITTING
Power-Up
The pointer will move counter clockwise to the stop pin and then moves to the current gauge reading. This procedure is an auto-calibration function and is
performed on every power-up. While this test is being performed, the gauge may make a clicking sound. This is normal.
Peak Recall
Press and hold the PeAK button to recall the highest temperature reading since the memory was last cleared. To clear the memory, press and hold the
PeAK button, and while still holding the PeAK button, press the WARN button. The pointer will move to the stop pin to indicate that the memory has been
cleared. Release the PeAK and WARN buttons to resume normal operation. The peak recall point is retained when power is removed from the gauge
Full Dial Warning
This gauge features full dial warning. When a warning point is reached, the entire dial illuminates in the programmed warning colour. This feature is available
for both a high and low warning set point. In addition, the warning colour will flash when an over warn point is reached.
Pro Control high Warning Set Point
To adjust the high warning set point, press and release the WARN
button. The warning light will begin to flash and the pointer will move to
the previous high warning set point signifying that warning set mode has
been selected. Once in set mode, press the WARN button
Pro Control high Over Warn Set Point
To adjust the high over warn set point, press and hold the WARN button.
After three seconds the warning light will begin to flash and the pointer will
move to the previous high over warning set point signifying that over warn
set mode has been selected. Release the warn button.
Pro Control Low Warning Set Point
To adjust the low warning set point, press and hold the WARN button, and
while still holding the WARN button, press and release the PeAK button.
The warning light will begin to flash and the pointer will move to the previous
low warning set point signifying that warning set mode has
Pro Control Low Over Warn Set Point
To adjust the low over warn set point, press and hold the WARN button,
and while still holding the WARN button, immediately press and hold the
PeAK button. After three seconds the warning light will begin to flash and
the pointer will move to the previous low over warning set point signifying
Change Backlight Colour
To change the backlight colour:
With power off, press and hold the warning button. Apply power to the
gauge. Release the WARN button. Press and release the PeAK button.
The pointer will move to half scale and the dial will illuminate with the current
Backlight Colour. Press and hold the PeAK button to cycle through the
B. Stainless Clamp Method
STAINLESS
CLAMP
to move the pointer down, or press the PeAK button to move the pointer
up. Three seconds after the last button press, the warning light will stop
blinking and the pointer will return to the current reading. The warning set
points are retained when power is removed from the gauge.
Once in set mode, press the WARN button to move the pointer down, or
press the PeAK button to move the pointer up. Three seconds after the last
button press, the warning light will stop blinking and the pointer will return
to the current reading. The over warn set points are retained when power is
removed from the gauge.
been selected. Once in set mode, press the WARN button to move the
pointer down, or press the PeAK button to move the pointer up. Three
seconds after the last button press, the warning light will stop blinking and
the pointer will return to the current reading. The warning set points are
retained when power is removed from the gauge
that over warn set mode has been selected. Release both buttons. Once
in set mode, press the WARN button to move the pointer down, or press
the PeAK button to move the pointer up. Three seconds after the last
button press, the warning light will stop blinking and the pointer will return
to the current reading. The over warn set points are retained when power is
.
removed from the gauge
available colours. Once you have selected the desired colour, release PeAK
and don't press any buttons for about three seconds. The dial will flicker
white several times to indicate the desired setting has been saved and the
gauge will return to normal operation with your new colour selection. Colour
selections are saved when power is off.
PROBE
SET SCREW
COLLAR
middle 2/3
.
.