Peg-Perego Agio Z3 Notice D'emploi page 15

as per the sequence shown in the
figure.
12 It can be adjusted into 2 positions:
POSITION 1: to use
POSITION 2: to attach the car seat
13 To remove the front bar, press down
on the buttons from both sides, as
per the sequence shown and remove
(fig_a).
It is possible to open the front bar on
one side only, so as to facilitate the
child's entry and exit (fig_b).
WARNING: The front bar has not
been designed to support the child's
weight; the front bar has not been
designed to lift the seat with the
child's weight. The front bar does not
replace the seat belt.
14 Before releasing the armrest,
unfasten the elastic from the cover
on both sides.
15 Slightly close the chassis.
Rotate the armrest to unfasten it
from the cap, as shown in figure
(fig.a).
To completely remove the armrest,
pull it outwards on both sides (fig.b).
Finally reattach the cover elastics to
the chassis.
16 Chassis without armrests. Keep the
armrests for a future use.
17 To reattach the armrests, proceed in
reverse sense. Pay attention to the
attachment direction.
When attaching the armrest, keep an
eye on the button, because it must be
in front of the armrest and not behind,
as shown.
Attach the armrests to the chassis as
shown.
18 HOOD: The hood comes with a loop
for hanging your child's favorite toy
(fig_a) and a see-through window for
observing your child (fig_b), which can
be lifted and fastened. You can detach
the Velcro, roll up the back of the hood
and fasten it at the top with the rubber
band to allow greater ventilation
during use with the backrest down
(fig_c). The hood may be pulled
forward into several positions (fig_d).
19 ADJUSTING THE BACKREST: to lower
the backrest, press the clip and the
backrest will move down to the
desired position.
To raise the backrest, press the clip
and lift the backrest to the desired
height.
20 FIVE POINT SAFETY HARNESS: To
fasten it, push the two waist strap
buckles (with the shoulder straps
attached – arrow_a) into the leg
divider until they click into place
(arrow_b). To unfasten it, press the
round button in the centre of the
buckle (arrow_c) and pull the waist
straps out (arrow_d).
21 To tighten the waist strap, pull on
both sides in the direction of the
arrow (arrow_a). To loosen it, move it
in the opposite direction.
22 Before adjusting the height of the
safety harness remove the shoulder
pads (fig_a). To adjust the height, slip
the belts through the eyelet in the
fabric (fig_b) and position them in
the most suitable eyelet.
23 FOLDING UP: To fold up the stroller,
we recommend ensuring the front
wheels swivel, closing the hood,
removing the car seat when fastened.
Align the handlebar and frame as
shown in the figure (fig_a).
Rotate the safety lever to the left
(fig_b) and pull the internal handle
towards yourself (fig_c).
24 Allow the handlebar to fall in on itself
until fully folded (fig_e).
The frame is folded correctly when
the side fastener automatically locks
(fig_f). Otherwise, gently press down
on the frame (fig_g).
The stroller is free-standing when
folded.
25 For greater compactness, it is
possible to remove the wheels.
To remove the rear wheels: pull the
pivot outwards and remove the
wheel as shown in the figure (fig_a).
To remove the front wheels: press
the tab as shown, and remove the
wheel (fig_b).
TRANSPORT: the stroller can be
carried comfortably locking the
front wheels and grasping the main
handle (fig_c).
26 REMOVABLE ITEMS: to remove
the hood, take the elastic off from
the buttons on the inside of the
handlebar (fig_a), detach the press
studs the sides of the chassis (fig_b),
detach the Velcro strip from the
- 15 -