Peg-Perego Agio Z3 Notice D'emploi page 14

NOTICE
THIS ARTICLE MEETS OR EXCEEDS
ALL REQUIREMENTS COVERED IN
ASTM F833 STANDARD AND LATEST
REVISIONS.
The images referring to the
textile details may differ from the
collection purchased.
For more information, consult our
website: www.pegperego.com
INSTRUCTIONS
1 OPENING: Before opening the frame,
remove (without using blades) any
die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE
FASTENER BEYOND ITS LIMIT.
_ DO NOT USE THE FASTENER AS
A CARRY HANDLE OR TO CARRY
WEIGHTS.
DO NOT HANG BAGS OR OTHER
ACCESSORIES TO THIS FEATURE.
Press down the side fastener, hold
the upper section of the handle and
rotate it towards you until the frame
is fully opened (fig_a). Open frame
(fig_b).
The frame is properly opened when
the attachment on the base clicks
into place, as shown.
2 FITTING THE WHEELS: Slot the
uprights into the rear wheel
crosspiece (fig_a), ensuring that it
is facing the right way, then push
the rear wheels on and make sure
that they click into place (fig_b). To
mount the front wheels, fit them into
the uprights until they lock into place
(fig_c).
3 ATTACHING THE MAIN HANDLE: if
the handle tube faces upwards, align
it with the stroller (Fig_a).
Fasten the handle to the frame as
shown in the figure (Fig_b).
To complete the operation, press
the two side buttons on the handle
(Fig_c) to ensure the handle pushes
in all the way, until it clicks into place
(Fig_d).
4 FITTING THE BASKET: if lowered, lift
the basket tube to the horizontal
position. Press the silver buttons
under the metal basket tube located
at the back of the stroller (fig_a)
and remove the metal tube (fig_b).
Thread the tube through the fabric
loop on the back of the basket,
making sure that the two silver
buttons are facing downward (fig_c).
Re-attach the tube to the housings
(fig_d).
5 Secure the two upper basket vinyl
eyelets to the two grey buttons on
either side of the metal tube housing.
Please note that the eyelets open
(fig_e).
IMPORTANT! Fasten the three lower
basket loops to the three grey
buttons on the rear bar fig_f).
WARNING! If this operation is not
completed properly, the basket will not
support any weight.
Fasten the front basket flaps to the
grey buttons on the frame (fig_g)
and then secure the basket centrally
to the footrest using the Velcro strap
(fig_h).
6 HOOD: Fasten the hood at the back
using the Velcro strip (fig_a), insert
the hood attachments into their
slots (fig_b), secure with the external
rubber band to the buttons on the
inside of the handlebar (fig_c), and
finally button the hood laterally to
the frame (fig_d).
7 FIXED OR SWIVELING FRONT
WHEELS: Lift the levers to prevent
the wheels from swiveling (fig_a) and
lower them to allow the wheels to
swivel (fig_b). On uneven surfaces,
the wheels should be set to their
fixed position.
8 BRAKE: Press the lever down to apply
the brake on the chassis and lift it to
release the brake.
9 ADJUSTABLE HANDLEBAR: To adjust
the height of the handlebar, press
both of the side buttons at the same
time (fig_a) and swing it into the
desired position (fig_b), then release
the buttons.
10 FOOTREST: before adjusting the foot
rest, ensure its cover is accurately
fitted; if it isn't, fit it accordingly.
To lower the footrest push the two
levers downwards and then push the
footrest downwards (fig_a); to raise
the footrest lift it upwards (fig_b).
11 FRONT BAR: insert the front bar
- 14 -