Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH - SR35i Segment Controller
Description
The SR35i is a Segment controller used in the
®
SiPass
Entro or Bewator Entro access control
system. A SR35i can control wired and wireless
doors at the same time. For example a SR35i/4 +
4 can control four wired and four wireless doors.
Safety
General safety precautions
•
Read the general safety precautions before
operating the device.
•
Follow all warnings and instructions marked
on the device.
•
Keep this document for reference.
•
Always pass this document on together with
the product.
•
The device has been approved for use in the
European Union. In countries outside the EU,
the local conditions and regulations need to be
checked before putting the device into service.
•
Please also take into account any additional
country-specific, local safety standards or
regulations concerning project planning,
operation and disposal of the product.
•
The device should only be used for indoor
applications.
Target group
Installer with expert knowledge of building
installation technique or electronic installations.
Standards and guidelines
European directives
This product complies with the requirements of
the European Directives. The European
declaration of conformity is available from:
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
DE-76181 Karlsruhe, Germany
European Directive 1999/5/EC on Radio
Equipment and Telecommunications Terminal
Equipment (R&TTE):
Compliance with the European Directive
1999/5/EC has been proven by testing according
to the following standards:
•
EN 301 489-1
•
EN 301 489-17
•
EN 300 328
•
EN 60950-1
2
Siemens Building Technologies
Fire Safety & Security Products
Technical data
Power supply
8 to 40 VDC or
8 to 30 VAC
Connect the device only
to power supplies which
have current limited
power source.
Power consumption
Power save
12V DC: 2.26 W
24V DC: 2.25 W
Full on
12V DC: 3.13 W
24V DC: 3.12 W
Temperature range
0 to +50 °C
Dimensions
182 x 248 x 66 mm
(H x W x D)
Details of ordering
Type
SR35i/xx
Part nr.
Siemens
/4 + 4: S54507-C1-A1
/8 + 8: S54507-C1-A2
/16 + 16: S54507-C1-A3
/32 + 32: S54507-C1-A4
Bewator
/4 + 4: GBI:31-904
/8 + 8: GBI:31-908
/16 + 16: GBI:31-916
/32 + 32: GBI:31-932
Description
Entro Segment Controller
Weight
0.98 kg
Configuration
See illustration on page 1 for reference
A
Lock to be opened with supplied special
key. (The door is not shown).
B1
The corners of the case can be lifted out.
B2
They provide knockouts for cable entry.
These are not interchangeable. They are
marked with the following numbers:
81284 (B1) = Lower left + upper right
corners.
81285 (B2) = Upper left + lower right
corners.
C
The box is fastened on the wall with four
screws.
Leave approx. 70 mm space around the
controller.
D
It is safe to route cables either over the
edge or via knockouts in the same edge.
Two anchor points for securing cables
with cable ties are provided at each
corner.
E
Local circuit (RS485).
Power supply:
Terminal 1 and 2.
Communication:
Terminal 3 and 4.
Screen:
Terminal 5.
The controller can be disconnected
without interrupting the local circuit.
Do not forget to use termination resistors
in the circuit ends.
F
Global circuit (RS485)
Communication:
Terminal 6 and 7.
Screen:
Terminal 8.
The controller can be disconnected
without interrupting the global circuit.
Do not forget to use termination resistors
in the circuit ends.
G
Three addressing knobs (001-016)
Disconnect the power supply before
changing the address.
H
Socket for compact flash memory card.
I
RS232 connection for PC, modem or
printer.
J, K
Two RJ45 Ethernet connections with a
switch function. 10/100 Mbit/s autosense
and autodetect of polarity.
Info: Compliance with the European
Directive 2004/108/EC „Electromagnetic
Compatibility" will be achieved only if the
device is equipped with a ferrite core.
Snap the ferrite core onto the Ethernet
cable within the SR35i box.
L
Battery socket. Type CR2032.
Note! Remove the isolating plastic band
to activate the battery poles.
M
Display used for configuring and address
or error information.
N
Tamper switch.
O
Antenna area. Make sure that the SR35i
is not mounted too close to metal objects.
02.2009
Publicité
Table des Matières
