WIKA S-10 Mode D'emploi page 6

7. Starting, operation
Assembly of L-connector DIN EN 17501-80 Form A
(D) Mounting hole
1. Loosen the screw (1).
2. Loosen the cable gland (2).
3. Pull the angle housing (5), with the
terminal block (6) inside, away from the
instrument.
4. Using the head of a small screwdriver in
the mounting hole (D), lever the terminal
block (6) out of the angle housing (5).
In order not to damage the sealing of the angle housing, do not try to push the terminal
block (6) out using the screw hole (1) or the cable gland (2).
5. Ensure that the conductor outer diameter you select is matched to the angle housing's
cable gland. Slide the cable through the cable gland nut (2), washer (3), gland seal (4) and
angle housing (5).
6. Connect the flying leads to the screw terminals on the terminal block (6) in accordance
with the pin-assignment drawing.
7. Press the terminal block (6) back into the angle housing (5).
8. Tighten the cable gland (2) around the cable. Make sure that the sealing isn't damaged
and that the cable gland and seals are assembled correctly in order to ensure ingress
protection.
9. Place the flat, square gasket over the connection pins on the top of the instrument
housing.
10. Slide the terminal block (6) onto the connection pins.
11. Secure the angle housing (5) and terminal block (6) to the instrument with the screw (1).
10 WIKA Operating instructions/Betriebsanleitung/Mode d'emploi/Instrucciones de servicio S-10, S-11
GB
(1)
(2)
(3)
(5)
(4)
Female
connector
(6)
Sealing
Clamping nut,
Male connector,
Case with
pressure connection
7. Starting, operation
Specifications Model S-10, S-11
Pressure ranges bar
Over pressure safety bar
Burst pressure bar
Pressure ranges bar
Over pressure safety bar
Burst pressure bar
Pressure ranges psi
Over pressure safety psi
Burst pressure psi
Pressure ranges psi
Over pressure safety psi
Burst pressure psi
Pressure ranges psi
Over pressure safety psi
Burst pressure psi
{Vacuum, gauge pressure, compound range, absolute pressure are available}.
1) Only model S-10.
For model S-11: The value specified in the table applies only when sealing is
2)
realised with the sealing ring underneath the hex. Otherwise max. 1,500 bar /
Specifications Model S-10, S-11
21,000 psi applies.
Materials
Wetted parts

» Pressure connection
» Pressure sensor
Case

Internal transmission fluid
4)
3) O-ring made of FPM/FKM for model S-11 with integrated cooling element.
4) Not for model S-10 with pressure ranges > 25 bar / 300 psi
WIKA Operating instructions/Betriebsanleitung/Mode d'emploi/Instrucciones de servicio S-10, S-11
0.1 0.16 0.25 0.4 0.6 1 1.6 2.5 4
1 1.5 2 2 4 5 10 10 17
2 2 2.4 2.4 4.8 6 12 12 20.5 42
25 40 60 100 160 250 400 600
50 80 120 200 320 500 800 1200
96 400 550 800 1000 1200 1700 2) 2400
50 INWC 100 INWC 5 10 15 25 30
14.5 29 29 58 72 145 145 240 500
29 35 35 69 87 170 170 290 600
200 300 500 600 1000 1500
1160 1160 1160 1160 1740 2900
1390 1390 5800 5800 7970 11,600
3000 5000 8000 10,000 1) 15,000
7200 11,600 17,400 17,400 21,750
17,400 24,650 2) 34,800 2) 34,800 43,500
(Other materials see WIKA diaphragm seal program)
316 Ti, S-11: O-ring: NBR 3) {FPM/FKM}
316 Ti (as of 40 bar / 600 psi 13-8 PH)
Stainless steel
Synthetic oil
GB
6 10 16
35 35 80
42 96
1000
1)
1500
2) 3000
60 100
2000
4600
14,500
1)
11