Refilling The Water Tank; Receiver Controls - Faber CAS500 Manuel D'utilisation

when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound.
Button panel 'B':- Controls the functioning of the left side of appliance
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
• is the reduce fire crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase fire crackling sound. Press this to increase the volume of the crackling sound.
GETTING THE DESIRED FLAME EFFECT
1. Switch the appliance on by pressing the main switch to the on position and pressing the on/standby button. The
flames will start after 45seconds. The flames will be at max height for 5seconds and then reduce to a nominal level
2. Press the and
to the changes you make.
3. Do not tilt or move the appliance while there is water in the tank or sump
4. Make sure that the appliance is on a level surface
Once you have made you adjustments to both the flame height and crackling sound the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you
switch on the appliance it will start up as normal, wait 45 seconds for the flames to start, run at maximum height for 5
seconds and then revert to the adjusted settings.

REFILLING THE WATER TANK

If you have chosen to operate your appliance by the Water Tanks provided, this section describes how to refill the Water
Tank on your CAS500 or CAS1000.
When the water in the tank(s) has been used up, the appliance will shut down the mist generation and cause the LED's
to continuously blink twice. In the case of a CAS1000 only one side of the product will blink, this is the side that has run
out of water. To refill follow the below steps;
1. Carefully lift off the fuelbed and set aside.
2. Press switch 'A' to the OFF (O) position.
3. Lift off the water tank, 1off on CAS500 and 2off on CAS1000 and take them to your water supply e.g. kitchen
4. Remove the cap by turning it anticlockwise
5. Fill with filtered tap water only
6. Replace the cap by turning it clockwise. Be careful not to over tighten
7. Place the bottle(s) back into position and wait until they finish filling the sump(s)
8. Press switch 'A' to the ON (I) position
9. Place the fuelbeds back on the product and make the DC connection see Fig7
10. Press on/standby on the receiver or the remote control to turn back on your appliance

RECEIVER CONTROLS

There are manual controls on the Receiver
CAS500
• is the on/standby button. Press it to turn on and off the flame effect.
• is the fire crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
• is the reduce flame button. Press this to reduce the height/intensity of your flame. You will hear an audible beep
when you reach the minimum level
• is the increase flame button. Press this to increase the height/intensity of your flame. You will hear an audible
beep when you reach the maximum level
CAS1000
• is the on/standby button. Press it to turn on and off the flame effect.
• is the fire crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
buttons to adjust the flame to your desired level. Please give the flame generator time to react
20