Chicco Fully Mode D'emploi page 7

FULLY ADAPTOR
IMPORTANT! READ CAREFULLY
AND KEEP
REFERENCE.
WARNING: BEFORE USE, REMOVE
AND DISPOSE OF ALL PLASTIC
BAGS AND PACKAGING MATERIALS
AND KEEP THEM OUT OF REACH OF
CHILDREN.
To install the Chicco KeyFit Child Car Seat, it is necessary to mount the
appropriate adaptor on the Chicco Fully stroller.
WARNINGS
• WARNING: The adaptor can only be
used with the Chicco Fully Stroller.
• WARNING: this adaptor can be
used for Chicco KeyFit child car
seats only.
• WARNING: Before use, check the
adaptor is correctly fixed to the
frame of the stroller.
• WARNING: Before use, make sure
that the child car seat is correctly fit-
ted in the adaptor by pulling it up.
• When not in use, keep the adaptor
out of reach of children.
ADVICES FOR CLEANING AND MAINTENANCE
The cleaning and maintenance of the product must only be carried out
by an adult.
CLEANING
After possible contact with water, dry the metal parts in order to avoid
the formation of rust. Do not use solvents or abrasive products for
cleaning. After use, keep the adaptor in a dry place.
To fasten and release the child car seat, read the below instructions.
1. The adaptor is supplied disassembled in its 4 parts (Fig. 1).
2. To assemble, insert one of the two tubes in the two side components
B-C until you hear it click into place (Fig. 2). Complete the operations
by engaging the second tube (Fig. 2A). Take care to place the two
tubes correctly with the joint facing upwards.
3. The adaptor is not installed (Fig. 3); when fastening the adaptor on
the frame, make sure to position the side with the protruding part of
the fasteners towards the handle of the stroller (Fig. 3A).
4. The adaptor can be mounted in the following configurations:
- single stroller: direct fastening on the frame (Fig.4 - 4A)
- single stroller: fastening on the frame with adaptors "1" (Fig. 4B)
- twin stroller: fastening on the frame with adaptors "1" and "4" (Fig. 4C)
USING SINGLE STROLLER CONFIGURATION
5. After having mounted the adaptor correctly, engage it on the joints
until you hear the click as described in images 4-4A, and mount the
FOR FUTURE
Chicco KeyFit Child Car Seat parent-facing (Fig. 5). At the end of use,
after removing the child car seat, unfasten the adaptor by pressing
the two side buttons (Fig. 5A).
USING SINGLE STROLLER CONFIGURATION WITH ADAPTOR "1"
6. Fasten the pair of adaptors "1" onto the frame parent facing (Fig. 6)
and then install the child car seat adaptor, it too parent-facing direc-
tion (Fig. 6A).
USING TWIN STROLLER CONFIGURATION
To use the Fully stroller with two child car seats, the following compo-
nents are needed:
- Adaptors "1"
- Adaptors "4"
- Two "KeyFit Fully adaptors"
7. Mount the adaptors "4" onto the rear leg tubes of the stroller, mak-
ing sure that the symbols present are correctly matched (Fig. 7 – 7A).
8. Install the adaptors "1" facing in the direction of travel on the central
joints of the stroller (Fig. 8).
9. Install the two adaptors for the child car seat on their respective
fasteners (Fig. 9- 9A). Complete the operation by mounting the two
child car seats onto the Fully adaptors (Fig. 9B).
10. Figures 10-10A-10B show all the possible options for using the
frame with Chicco KeyFit child car seats only.
WARRANTY
The product is guaranteed against any conformity defect in normal
conditions of use as stated in the instructions. Therefore, the warranty
does not apply in the case of damage caused by improper use, wear or
accidental events. For the duration of the warranty on conformity de-
fects please refer to the specific provisions of applicable national laws
in the country of purchase, where appropriate.
7