Backlight - Briteq BT-BEAM60 Mode D'emploi

ENGLISH
 Show 3: Fixture is placed on a podium, in front of the
audience. The spot is always projecting to the audience's
direction; i.e. in front of the stage. Pan movement angle
(left to right to left): 160°. Tilt movement angle: 90° (60°
above horizon; 30° below horizon.)
 Show 4: Fixture is fixed under ceiling. The spot is mainly
projecting in front of the stage. Pan movement angle (left
to right to left):160°. Tilt movement angle: 90° (vertically,
front 75°; back 15°)
 Once the right mode shows on the display, press the ENTER
button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
Split Color
You can select if the unit can only show full colors or also
split colors.
 Press the MENU button until "Split color" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "Yes" (Split colors) or "No"
(only full colors).
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
Slave Mode
Used to make the slave unit work in opposite to the master
or to work in complete sync.
 Press the MENU button until "Slave Mode" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select Slave1 (normal) or Slave2
(2 light show) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit
goes in blackout and waits for the DMX-signal.
No blackout mode: when no DMX-signal is detected, the unit
automatically switches to standalone mode.
 Press the MENU button until "Black Out" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "Yes" (blackout on) or
"No" (blackout off) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the MENU
button for about 2 seconds.
BRITEQ
®
OPERATION MANUAL
5/74 BT-BEAM60
ENGLISH
Sound State
The unit works to rhythm of the beat when used in standalone or master/slave mode
 Press the MENU button until "Sound State" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "On" or "Off" mode.
 Once the mode is selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Sound Sense
Used to set the sensitivity of the internal microphone
 Press the MENU button until "Sound Sense" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select a value between "0" (very low sensitivity) and "100" (high sensitivity).
 Once the mode is selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Pan Invert
Normal: Panning movement is not inverted.
Pan inversion: Panning movement is inverted
 Press the MENU button until "Pan Invert" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "No" (normal) or "Yes" (pan inversion) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Tilt Invert
Normal: Tilt movement is not inverted.
Tilt inversion: tilt movement is inverted
 Press the MENU button until "Tilt Invert" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "No" (normal) or "Yes" (tilt inversion) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.

Backlight

Backlight on: display is always on.
Backlight off: display is off when not used.
 Press the MENU button until the display shows "Back Light".
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select "On" (display always on) or "Off" (display off when not used).
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Focus Adjust
Used to help you adjusting the focus of the rotating gobos
 Press the MENU button until the display shows "Focus Adjust".
 Press the ENTER button so the unit goes to the "home" position.
You are able to adjust the focus with the UP/DOWN buttons on the unit (the display shows the current focus
status).
Attention: please note that you can only set an "average focus", so it is not possible to set the focus
perfectly sharp for all directions.
 To go back to the functions press the MENU button.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
BRITEQ
®
OPERATION MANUAL
6/74 BT-BEAM60