Setup Requirements - Anglecare AC417 Manuel Du Propriétaire

12.14 Overloading - DO NOT overload wall outlets, extension cords or
integral convenience receptacles as this can result in a risk of fire or
electric shock.
12.15 Object and Liquid Entry - NEVER push objects of any kind into this
product through casing slots as they may touch dangerous voltage points
or short out parts that could result in a risk of fire or electric shock. NEVER
spill liquid of any kind on the product.
12.16 Antenna - The antenna used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all persons and
must not be collocated or operating in conjunction with any other antenna
or transmitter.
12.17 Power Lines - An outside antenna system should NOT be located
in the vicinity of overhead power lines or other electric light or power
circuit, or where it can fall into such power lines or circuits as contact
with them may be fatal.
12.18 Vibration Source - When the monitor is in use, DO NOT use a bedside
crib, crib mobile or other crib accessories that may produce vibrations.
Other sources of vibrations may include fans, washing machines, loud
music, etc. These sources of vibration may interfere with the performance
of your Angelcare monitor and the alarm will not sound if it continues to
®
detect any movement other than your baby's. Be sure all vibration sources
are eliminated before using the monitor.
12.19 You may experience false alarms for several reasons. The
most common reason is the Camera has not been turned OFF
after you have removed your baby from the crib. Another reason is
the Sensor Pad has not been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm surface with the Angelcare
side facing up. The sensitivity level may also need to be adjusted. Refer
to Step 5.1. Always be sure to immediately check on baby whenever an
alarm sounds.
12.20 Sensor Pad - Your Sensor Pad can be used in any crib that is stationary.
If the crib has a spring or slat base, place a hard board between the crib
base and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.
Only use your Angelcare monitor in a stationary sleeping environment such
®
as a crib where the Sensor Pad can rest on a completely flat, firm surface.
The Sensor Pad is made of plastic and does not permit the
air to circula te. T here fore, mildew build up could develop
underneath the mat tress in the Sensor Pad area. We suggest
r o t a t i n g t h e m a t t r e s s r e g u l a r l y t o p r e v e n t a n y m i l d e w.
13. IMPORTANT SAFETY INSTRUCTIONS RELATED TO USE OF BATTERIES
13.1 Use ONLY the type and size of battery specified in the owner's manual.
There is a risk of explosion if battery is replaced with an incorrect type.
13.2 Charge the battery for 9 hours prior to first use. Be sure to have the
monitor in the OFF position during this period. ONLY use the adapters
included with your monitor.
13.3 DO NOT use these adapters with any other equipment.
13.4 When unplugging the adapter from the Camera, be sure it is switched
to the OFF position.
13.5 DO NOT dispose of batteries in fire. They may explode. Check with
local regulations for possible special disposal instructions.
13.6 Exercise care in handling batteries in order not to short out the
batteries with conducting materials such as rings, bracelets and keys.
Overcharging, short circuiting, reverse charging, mutilation, or incineration
of batteries must be avoided to prevent one or more of the following
occurrences: release of toxic materials, release of hydrogen and/or oxygen,

SETUP REQUIREMENTS

INCLUDED:
Touchscreen Parent Unit
Wireless movement Sensor Pad
* Always place Angelcare logo side up *
®
gas and rise in surface temperature.
13.7 DO NOT attempt to rejuvenate the battery provided with or identified
for use with this product by heating them. Sudden release of battery
electrolyte may occur, causing burns or irritation to eyes or skin.
13.8 If and when necessary, the battery must be replaced with identical
new ones or equivalent (volts and size).
13.9 Remove the battery from the Parent Unit if you store the product
over 30 days because the battery could leak and damage the product.
13.10 Discard 'dead' batteries as soon as possible since 'dead' batteries
are more likely to leak in a product. If a battery has leaked or vented, it
should be replaced immediately using protective gloves.
13.11 DO NOT store this product, or the battery provided with or identified
for use with this product, in high-temperature areas.
14. Modifications not authorized by the manufacturer may void users
authority to operate this device.
14.1 NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications.
logo
®
14.2 However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
14.3 This device complies with the part 15 of the FCC Rules and the
Industry Canada license - exempt RSS standards(s). Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
IC Warning :
15. This device complies with industry Canada RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including inferences that
may cause undesired operation of the device.
15.1 Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Camera Unit
Tabletop stand with removable
wall mount metal ball
2X
2x AC adapter
(for Parent Unit and
Camera Unit)
WARNING
(North America Only)
Model AC417 and AC517
Baby Breathing Monitor, with Video
(for Camera Unit)
Lithium ion
battery pack
(for Parent Unit)
E
N
Hardware
(Screwdriver required
for wall mounting)
CR3032 battery
(for Sensor Pad)
3