Operating Instructions; Delay Start - IKEA ESSENTIELL Mode D'emploi

EN
Heat Dry/Air Dry
Use of the Heat Dry option, especially in Use of the Heat Dry option, especially in
combination with use of rinse agent, will combination with use of rinse agent, will
enhance drying. If Air Dry is selected the enhance drying. If Air Dry is selected the
heater will be de-activated during the drying heater will be de-activated during the drying
phase of the selected wash cycle. This will phase of the selected wash cycle. This will
slightly lower the energy use but will increase slightly lower the energy use but will increase
the likelihood that the dishware will not dry the likelihood that the dishware will not dry
completely. completely.
Max Dry
When Max Dry option is selected, the When Max Dry option is selected, the
dishwasher extends drying time by dishwasher extends drying time by
approximately 20 minutes. The Max Dry approximately 20 minutes. The Max Dry
option can be used with all cycles except China option can be used with all cycles except China
Crystal, Energy Saver, and Rinse Only. For best Crystal, Energy Saver, and Rinse Only. For best
drying performance, also apply an increased drying performance, also apply an increased
wash temperature by selecting Hi-Temp Wash wash temperature by selecting Hi-Temp Wash
or even better, the Sanitize option. or even better, the Sanitize option.
The energy required to use the Max Dry option The energy required to use the Max Dry option
costs pennies per cycle. You may choose not costs pennies per cycle. You may choose not
to select the Max Dry option; however you to select the Max Dry option; however you
may have items in your dish load that will not may have items in your dish load that will not
be completely dry at the end of the cycle. be completely dry at the end of the cycle.
Sanitize Option
To sanitize your dishes and glassware, select To sanitize your dishes and glassware, select
the Sanitize option. When selected, the the Sanitize option. When selected, the
indicator light will come on and remain on until indicator light will come on and remain on until
the end of cycle. The water temperature in the the end of cycle. The water temperature in the
final rinse will be raised to 156 final rinse will be raised to 156
option is available in Power Plus, Normal Wash option is available in Power Plus, Normal Wash
and Top Rack Cycles. Only these sanitization and Top Rack Cycles. Only these sanitization
cycles have been designed to meet NSF cycles have been designed to meet NSF
requirements. requirements.
The cycle time will be extended until the proper The cycle time will be extended until the proper
water temperature is reached. Washing water temperature is reached.
action will continue during the water heating action will continue during the water heating
delay. For best results, the incoming water delay. For best results, the incoming water
temperature should be at least 120 temperature should be at least 120
The sanitize criteria may not be satisfied if there The sanitize criteria may not be satisfied if there
is an interruption of the cycle, power failure or if is an interruption of the cycle, power failure or if
the incoming water temperature is below 120 the incoming water temperature is below 120
(49 (49 C). C).
o o
To turn off the Sanitize option, press Sanitize a To turn off the Sanitize option, press Sanitize a
second time. The indicator light will turn off. second time. The indicator light will turn off.

OPERATING INSTRUCTIONS

F (69 F (69 C). This C). This
o o o o
Washing
F (49 F (49 C). C).
o o o o
F F
o o
Favorite Cycle
The Favorite Cycle option allows you to The Favorite Cycle option allows you to
program your preferred cycle and options into program your preferred cycle and options into
one button. Once Programmed, simply select one button. Once Programmed, simply select
Favorite Cycle and then select START/Cancel. Favorite Cycle and then select START/Cancel.
To Program the Favorite Cycle: To Program the Favorite Cycle:
1. 1. Select your preferred cycle and options Select your preferred cycle and options
2. 2. Press Favorite Cycle for 3 seconds. Press Favorite Cycle for 3 seconds.
The display will flash for 2 seconds The display will flash for 2 seconds
indicating the Favorite Cycle option has been indicating the Favorite Cycle option has been
programmed. To change the Favorite Cycle programmed. To change the Favorite Cycle
option simply repeat steps one and two option simply repeat steps one and two
above. above.

Delay Start

The Delay Start option allows you to
automatically delay starting your dishwasher
1-24 hours.
To start the Delay Start option, press Delay
Start until the desired delay time shows in the
Status window. A light will come on indicating
the delay has been set and will remain on until
cycle starts. Press the START/Cancel pad to
start the delay option. If the delay option is
interrupted, the START/Cancel pad will have to
be pressed again to return to delay option.
To cancel the Delay Start option and to begin
the selected cycle before the delay period
is over, press and hold START/Cancel pad for
3 seconds.
To Cancel a Cycle
You can cancel a cycle anytime during the
cycle. Press and hold the START/Cancel pad
for 3 seconds. The light above the cycle and
option selected will go out, and the START/
Cancel light will remain illuminated, the
dishwasher will start a 90 second drain. At the
end of the drain, select the next desired cycle.
Child Lock Controls
To prevent children from accidently changing To prevent children from accidently changing
the dishwasher cycle or starting the the dishwasher cycle or starting the
dishwasher, to lock the dishwasher controls dishwasher, to lock the dishwasher controls
press and hold Delay Start for 3 seconds. An press and hold Delay Start for 3 seconds. An
indicator light on the lock graphic pad will indicator light on the lock graphic pad will
illuminate when the controls are locked and no illuminate when the controls are locked and no
new selections can be made until the lock is new selections can be made until the lock is
released. To unlock the controls, press Delay released. To unlock the controls, press Delay
Start again for 3 seconds, and the indicator Start again for 3 seconds, and the indicator
light will go out. light will go out.
7