Briteq BT-70LS Mode D'emploi page 8

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

ENGLISH
OPERATION MANUAL
Sound Sense
Used to set the sensitivity of the internal microphone
 Press the MENU button until "Sound Sense" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to choose a value between "0" (very low sensitivity) and "100" (high sensitivity).
 Once the right value is shown on the display, press the ENTER button select it.
 Press the MENU button for about 2 seconds to store the setting and to return to running mode.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
 Press the MENU button until "Pan Inverse" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "No" (normal) or "Yes" (pan inversion) mode.
 Once the mode is selected, press the ENTER button to select it.
 Press the MENU button for about 2 seconds to store the setting and to return to running mode.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
 Press the MENU button until "Tilt Inverse" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to choose "No" (normal) or "Yes" (tilt inversion) mode.
 Once the right mode is shown on the display, press the ENTER button to select it.
 Press the MENU button for about 2 seconds to store the setting and to return to running mode.
Backlight
Backlight on: display is always lit.
Backlight off: display is dark when not used.
 Press the MENU button until the display shows "Back Light".
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select "On" (display always lit) or "Off" (display dark when not used).
 Once the right mode is shown on the display, press the ENTER button to select it.
 Press the MENU button for about 2 seconds to store the setting and to return to running mode.
Focus Adjust
Used to help you adjusting the focus of the rotating gobos (gobo wheel1).
 Press the MENU button until the display shows "Focus Adjust".
 Press the ENTER button so the unit goes to the "tilt 90°" position.
 Press the ENTER button so the unit goes to the "pan 0°" position.
 Press the ENTER button so the unit goes to the "pan 90°" position.
 Press the ENTER button so the unit goes to the "pan 180°" position.
 Press the ENTER button so the unit goes to the "pan 270°" position.
In the Previous 5 steps you are able to adjust the focus with the UP/DOWN buttons on the unit (the display
shows the current focus status).
Attention: please note that you can only set an "average focus" for all 5 positions, so it is not possible to set
the focus perfectly sharp for all directions.
 To go back to the functions press the MENU button.
Function Delay
On the Function channel (CH14 or CH15) you can select some special functions, like "blackout
during gobo change" and others. With this option you can select the delay before a selected function
becomes active.
IMPORTANT INFORMATION: the function delay can only be set to zero seconds (no Delay) when you are
using a DMX-controller or DMX-software using presets for the DMX-values of the special functions.
Never use "no Delay" while using a simple DMX-controller with faders to set the functions manually!
 Press the MENU button until "Function Delay" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to choose a value between "no Delay" / "1s Delay" / "2s Delay" or "3s Delay" /
BRITEQ
6/79
BT-70LS
®

Publicité

Table des Matières
loading

Table des Matières