Safety Instructions Governing Specific Operational Phases; Special Work Related To The Maintenance And Repair Of The Machine - GÖLZ FS125 Mode D'emploi Et Liste Des Pièces De Rechange

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

FS125
directed and supervised by qualified personnel in
compliance with the respective rules!
2.5
Safety instructions governing
specific operational phases
Before work
Avoid any operational mode that might be prejudicial to
safety!
Before beginning work, familiarize yourself with the
surroundings and circumstances of the site, such as
obstacles in the working and travelling area, the soil
bearing capacity and any barriers separating the
construction site from public roads.
Take the necessary precautions to ensure that the
machine is used only when in a safe and reliable state.
Operate the machine only if all protective and safety-
oriented devices, such as removable safety devices,
emergency
shut-off
elements and exhausters, are in place and fully
functional.
Regard all safety specifications!
Check the machine at least once per working shift for
obvious damage and defects. Report any changes
(incl. changes in the machine's working behaviour) to
the competent organization/ person immediately. If
necessary, stop the machine immediately and lock it.
Have any defects rectified immediately. At any time,
ensure the operator has sufficient view to his working
area, in order to have intervention to the working
process.
Wet cutting is to be accomplished while working. This
prevents the appearance of particulate matter and
increases the life-time of the diamond tool. During
start-up and shut-down procedures always watch the
indicators
in
accordance
instructions!
Before starting or setting the machine in motion, make
sure that nobody is at risk. Keep children and
unauthorized persons away from the work area.
Noise protection equipment on the unit must be in
protective position during operation. Wear the required
individual ear protection!
Always keep at a distance from the edges of building
pits and slopes. Avoid any operation that might be a
risk to machine stability! Keep the work area clean.
Cluttered areas and benches invite injuries! Do not
operate when you are tired! Watch what you are doing!
Risk of stumbling! Cables and hoses must complete
rolling up. After assembly do not leave any tools, a
wrench for example, on the unit.
Check to see that the tools are removed from the
machine before operating! Damaged blades have to
be changed immediately. Use only recommended
®
blades from the GÖLZ
Control the working area for water-, gas- and electrical
lines!
equipment,
sound-proofing
with
the
operating
GmbH.
Important:
accomplished while working! This
prevents the appearance of particulate
matter and increases the life-time of
the diamond tool!
During work
Make sure, that the machine is well fastened before
and while cutting!
Never touch rotating parts like blade shaft or blade!
After work
Before leaving the machine always secure it against
unauthorized use!
2.6
Special work related to the
maintenance and repair of the
machine
Observe the adjustment, maintenance and inspection
activities and intervals set out in the operating
instructions, including information on the replacement
of parts and equipment! These activities may be
executed by skilled personnel only.
Brief operating personnel before beginning special
operations or maintenance work, and appoint a person
to supervise the activities.
In any work concerning the operation, conversion or
adjustment of the machine and it's safety-oriented
devices or any work related to maintenance, inspection
and repair, always observe the start-up and shut-down
procedures described in the operating instructions and
the information on maintenance work. Ensure that the
maintenance area is adequately secured.
Carry out maintenance and repair work only of the
machine is positioned on stable and level ground and
has been secured against inadvertent movement and
buckling. If the machine is completely shut down for
maintenance and repair work, it must be secured
against inadvertent starting.
To avoid the risk of accidents, individual parts and
large assemblies being moved for replacement
purposes should be carefully attached to lifting tackle
and secured. Use only suitable and technically perfect
lifting gear and suspension systems with adequate
lifting capacity. Never work or stand under suspended
loads.
The fastening of loads and the instructing of crane
operators should be entrusted to experienced persons
only. The marshaller giving the instructions must be
within sight or sound of the operator.
For carrying out overhead assembly work always use
specially designed or otherwise safety-oriented ladders
and working platforms. Never use machine parts as a
climbing aid. Wear safety harness when carrying out
maintenance work at greater heights.
- 26-
Wet
cutting
is
to
5009002-00
BA-DE-GB-FR-NL (001)
®
be

Publicité

Table des Matières
loading

Table des Matières