Organisational Measures; Selection And Qualification Of Person - GÖLZ FS125 Mode D'emploi Et Liste Des Pièces De Rechange

FS125
2.3

Organisational measures

This operating manual must always be at hand at the
place of use of the machine and must be accessible to
the person operating the machine!
In addition to this operating manual, all other generally
applicable legal and other mandatory regulations
relevant to accident prevention and environmental
protection must be observed! Such obligations may
also comprise the handling of hazardous materials,
provisioning and/ or wearing of personal protective
equipment, or road traffic regulations.
This operating manual must be supplemented by
instructions covering the duties involved in supervising
and notifying special organizational features, such as
job organization, work flows or the person entrusted
with the work. Person entrusted with work on the
machine must have read the operating manual prior to
taking up work. This applies especially to persons
working only occasionally on the machine, e.g. during
set-up or maintenance activities.
Check - at least from time to time - whether the
personnel is carrying out the work in compliance with
the operating manual and paying attention to risks and
safety-relevant factors.
For reasons of safety, long hair must be tied back or
otherwise secured, garments must be close-fitting and
no jewellery - including rings - may be worn.
Severe injury may result from being caught by moving
parts of the machine. Personal protective equipment
must be used wherever required by the circumstances
or by law (e.g. safety glasses, ear protectors, safety
boots, suitable safety
regulations for prevention of accidents! Observe all
safety precautions and warnings attached to the
machine and always keep them in good and perfectly
legible condition.
The personal protection equipment should consist
of the following parts:
1) Hard hat with ear muff
2) Visor or safety glasses
3) Dust mask
4) Protective gloves
5) Safety clothes
6) Safety boots
clothing). Observe
In case event of safety-relevant modifications or
changes in the behaviour of the machine, stop the
machine immediately and report the malfunction to the
competent authority/ person. Do not remove or make
inoperative any safety devices the machine is
equipped with.
Never make
conversions which might affect safety without GÖLZ
GmbH prior approval! This also applies to the
installation and adjustment of safety devices as well as
to welding and cutting work on supporting structures.
Damaged or worn parts of the product must be
replaced immediately. Use genuine spare parts only.
All spare parts and tools must comply with the
technical requirements specified by the manufacturer/
distributor. Adhere to the legally prescribed preventive
maintenance and
specified in this operating manual!
Hydraulic hose pipes must be changed within the
specified or appropriate intervals, even if no safety-
relevant defects are visible.
All maintenance and repair activities must be
performed by qualified personnel using suitable tools
and other suitable workshop equipment. Observe the
fire alarm and fire fighting measures. The personnel
must be made familiar with the location and handling
of fire extinguishers!
2.4 Selection and qualification of
person
the
Only permitted personnel is allowed to work on and
with the machine! The legal minimum age is to be
observed!
Only assign trained and instructed personnel! Clearly
define the responsibilites of the personnel with regard
to operating, setting-up, maintaining and repairing the
machine! The GÖLZ
your personnel.
Make sure that only instructed and competent
personnel works
responsibility of the machine operator, also in terms of
traffic regulations and enable him to refuse instructions
of third parties which breach safety regulations.
Personnel that is to be trained or to be instructed or
that is serving a general training is only to be permitted
to operate the machine under the supervision of an
experienced person.
To operate the machine you must be rested, in good
physical condition and mental health. If you have any
condition that might be aggravated by strenuous work,
check with your doctor before operating with the
machine. Do not operate the machine if you are under
the influence of any substance (drugs, alcohol) which
might impair vision, dexterity or judgment.
Works on electrical, pneumatic, combustion and
hydraulic fittings and equipment are only to be carried
out by qualified personnel or instructed people being
- 25-
any modifications,
inspection intervals
®
GmbH can assist you in training
on the machine.
BA-DE-GB-FR-NL (001)
®
additions or
®
or those
Define the
5009002-00