Remote Control Power Supply; Measuring Tool Power Supply - Bosch GRL 250 HV Professional Notice Originale

20 | English
Rotary laser
Weight according to EPTA-Procedure 01:2014
Dimensions (length × width × height)
Protection rating
A) At 25 °C
B) The working range may be reduced by unfavourable environmental conditions (e.g. direct sunlight).
C) Along the axes
D) Only non-conductive deposits occur, whereby occasional temporary conductivity caused by condensation is expected.
The serial number (16) on the type plate is used to clearly identify your measuring tool.
Remote control
Article number
A)
Working range
Operating temperature
Storage temperature
Max. altitude
Relative air humidity max.
Pollution degree according to IEC 61010-1
Battery
Weight according to EPTA-Procedure 01:2014
A) The working range may be reduced by unfavourable environmental conditions (e.g. direct sunlight).
B) Only non-conductive deposits occur, whereby occasional temporary conductivity caused by condensation is expected.
For clear identification of your remote control, see the serial number (27) on the type plate.
Assembly

Remote Control Power Supply

Using alkali-manganese batteries is recommended to oper-
ate the remote control.
To open the battery compartment cover (29), push the lock-
ing mechanism (28) in the direction of the arrow and re-
move the battery compartment cover. Insert the battery.
When inserting the batteries, ensure that the polarity is cor-
rect according to the illustration on the inside of the battery
compartment.
Remove the battery from the remote control when not
u
using it for longer periods. The battery can corrode and
self-discharge in the remote control during prolonged
storage.

Measuring Tool Power Supply

Inserting/changing the batteries
It is recommended that you use alkaline manganese batter-
ies to operate the measuring tool.
To remove the battery compartment (13), turn the locking
mechanism (14) to position . Pull the battery compart-
ment out of the measuring tool and insert the batteries.
When inserting the batteries, ensure that the polarity is cor-
rect according to the illustration on the inside of the battery
compartment.
1 609 92A 7AR | (07.02.2022)
GRL 250 HV
1.8 kg
190 × 180 × 170 mm 190 × 180 × 170 mm 190 × 180 × 170 mm
IP54 (dust and splash- IP54 (dust and splash-
proof)
Always replace all the batteries at the same time. Only use
batteries from the same manufacturer and which have the
same capacity.
Slide the battery compartment (13) into the measuring tool
and turn the locking mechanism (14) to position .
Take the batteries out of the measuring tool when you
u
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
storage in the measuring tool.
Charge-control indicator
When the battery warning (12) flashes red for the first time,
the measuring tool can still be operated for approx. 2 hours.
When the battery warning (12) lights up red continuously,
no further measurements can be taken. The measuring tool
switches off automatically after 1 minute.
Operation
Protect the measuring tool and remote control against
u
moisture and direct sunlight.
Do not expose the measuring tool or remote control to
u
any extreme temperatures or variations in temperat-
ure. For example, do not leave them in a car for extended
periods of time. In case of large variations in temperature,
allow the measuring tool and the remote control to adjust
to the ambient temperature before putting them into op-
eration. Before continuing work with the measuring tool,
always perform an accuracy check (see "Accuracy Check
GRL 300 HV GRL 300 HVG
1.8 kg 1.8 kg
IP54 (dust and splash-
proof) proof)
RC 1
3 601 K69 9..
30 m
–10 °C to +50 °C
–20 °C to +70 °C
2000 m
90 %
1 × 1.5 V LR6 (AA)
0.07 kg
Bosch Power Tools
B)
2