Technical Data; Maintenance And Cleaning - Speaka Professional 1082615 Mode D'emploi

Operation
• Turn off all devices to be connected.
• Connect one monitor to the HDMI output (11) using the HDMI cable of the monitor.
• Connect a USB keyboard and a USB mouse to the mouse USB port (1) and keyboard USB
port (2) respectively.
• Connect the USB port of the first computer to the USB-A plug and the PC1 USB-B port (13)
to the USB-B plug of the HDMI USB cable provided.
• Connect the HDMI port of the computer to the PC1 HDMI input (12) using the HDMI plug of
the HDMI USB cable provided.
• Follow the same instructions as mentioned under steps 4 and 5 in order to connect a second
computer to the PC2 HDMI and USB ports.
• If needed, connect another device such as an external hard drive to the Console USB
port (3). Use the microphone socket (4) and headphones jack (5) to connect respective
audio accessories. Press the Audio ON/OFF button (7). The green audio LED (6) lights up
indicating that the audio channel is enabled. Press the Audio ON/OFF button again to mute
audio output.
• Connect the round plug of the power adapter to the 5 V/DC, 2 A socket (10) and the mains
plug of the power adapter provided to a normal wall outlet.
• Turn on the computer connected to PC1 port and wait until it has started up. Once the
computer has properly completed installation and start-up operations, press the Select
button (9) to select PC1. With each time pressing the Select button, the blue LED (8)
alternates between PC1 and PC2. Check if all connected devices function properly.
• Then turn on the computer connected to PC2 port. Once it has properly completed installation
and start-up operations, press the Select button to select PC2. Check if all devices connected
function properly. The installation is then complete and the device ready for operation.
Note that at least one of the devices connected must be a computer with USB port.
Otherwise the switching mechanism will not function.
a) Hotkeys
Once you have activated the hotkey mode, you can use key kombinations on the keyboard
to control the switch. The below table lists possible functions and the corresponding key
kombinations.
Function
Start hotkey mode
Switch to the next active port
Switch to the desired port (1 or 2)
Lock and unlock current output channel:
1 – Lock
0 – Unlock (Default)
Switch to newly connected hosts:
1 - Enable
0 - Disable (Default)
Enable/disable buzzer:
1 - Enable (Default) (*)
0 - Disable
Auto-scan on (**)
Reboot and enter IAP mode to update the
firmware
Notes :
(*) Buzzer sound:
• Hotkey activated: 1 beep
• Error: 2 beeps
(**) On the keyboard, press the space bar to stop the scan.
On the keyboard, press any key other than the space bar to stop the scan and
activate the first input channel.

Maintenance and cleaning

• Before cleaning, disconnect the product from the connected devices and unplug the power
adapter from the power outlet.
• There are no components located inside the product you need to maintain. Never open/
dismantle the product.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• To clean the product, a dry, soft and clean cloth is sufficient. Do not apply too much pressure
to the housing to prevent scratching.
Key kombinations
Scroll Lock + Scroll Lock
Scroll Lock + Scroll Lock + [Enter]
Scroll Lock + Scroll Lock + [N]
Scroll Lock + Scroll Lock+ P + W + [0/1]
Scroll Lock + Scroll Lock +
P + L + U + G + [0/1]
Scroll Lock + Scroll Lock + B + [0/1]
Scroll Lock + Scroll Lock + S
Scroll Lock + Scroll Lock + U + [Enter]
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.

Technical data

a) KVM switch
Inputs ............................................ 2 x HDMI, 2 x USB-B, 1 x USB-A
Outputs ......................................... 1 x HDMI, 1 x USB keyboard, 1 x USB mouse,
HDMI resolution (input) ................. 2160p / 1080p / 1080i / 720i / 720p / 480p or
PC's UXGA 1920x1200
System requirements .................... Windows
only 32 bit), Vista™ (32 / 64 bit), 7 (32 / 64 bit), 8,
8 ProMac OS 10.8 and higher versions, Linux Kernel 2.6.x
Operating conditions ..................... 0 to +40 ºC, 20 – 90 % RH (non-condensing)
Storage conditions ........................ -20 to +60 ºC, 20 – 90 % RH (non-condensing)
Cable length ................................. 170 cm (HDMI USB cable)
with 10 cm USB-B cable and 30 cm USB-A cable
Dimensions (W x H x D) ............... 154 x 23 x 69 mm
Weight .......................................... 268 g (without cable)
b) Power adapter
Input voltage / current ................... 100 – 240 V/AC, 50/60 Hz, max. 0.5 A
Output voltage / current ................ 5 V/DC, 2 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE.
XP (Home, Pro, with SP1, SP2, SP3,
®
*1082615_v3_0421_02_jh_m_en