Stand-Alone M Ode - HQ Power VDPL3 0 0 MR Mode D'emploi

• Use t he o rigina l pack aging if t he dev ice is t o be t ranspo rt ed.
• All m o dificat io ns o f t he dev ice are fo rbidden fo r safety reaso ns.
• Only use t he dev ice fo r it s int ended purpo se. All o t her uses m ay lead to sho rt circuit s, b urns,
elect rosho cks, crash, et c. Using t he dev ice in an unaut ho rised w ay w ill v o id t he w arrant y .
• The inst allat io n has to be appro v ed by an ex pert befo re t he dev ice is t ak en int o serv ice.
• Co nnect t he dev ice to t he m ains w it h t he power plug. Do n't co nnect it t o a dim m ing pack .
4 . I n st alla tion
• Hav e t he dev ice inst alled by a qua lif ied perso n, respect ing EN 6 05 98- 2- 17 and all o t her applicable
no rm s.
• The carry ing co nst ruct io n m ust be able to suppo rt 1 0 t im es t he w eight o f t he dev ice fo r 1 ho ur w it ho ut
defo rm ing.
• The inst allat io n m ust alway s be secured w it h a seco ndary at t achm ent e.g. a safet y cable.
• Nev er stand direct ly be lo w t he dev ice w hen it is be ing m o unt ed, rem ov ed o r serv iced. Hav e a qualif ied
t echnician check t he dev ice o nce a year and o nce befo re yo u bring it int o serv ice.
• Inst all t he dev ice in a lo cat io n w it h few passers- by t hat is inaccessible t o unaut ho rised perso ns.
• Ov erhead m o unt ing requ ires ex t ensiv e ex perience: calculat ing w o rk load lim it s, det erm ining t he
inst allat io n m aterial t o be used... Hav e t he m aterial and t he dev ice it self check ed regularly . Do no t
at t em pt to inst all t he dev ice yo urself if y o u lack t hese qualif icat io ns as im pro per inst allat io n m ay result
in inj ur ies.
• Adj ust t he desired inc linat io n angle v ia t he m o unt ing brack et and t ight en t he brack et screws.
• Make sure t here is no flam m able m aterial w it h in a 0 .5 m radius o f t he dev ice.
• Hav e a qualif ied e lect ric ian carry o ut t he elect ric co nnect io n.
• Co nnect t he dev ice to t he m ains w it h t he power plug. Do not co nnect it to a dim m ing pack .
• The inst allat io n has to be appro v ed by an ex pert befo re t he dev ice is t ak en int o serv ice.
5 . Fe atu re s
• DMX- co nt ro lled v ia 2 channels
• so und- act iv at ed st and- alo ne m o de o r DMX m ode
• adj ust able ro t at io n speed v ia DMX m o de
6 . Ove rview
Please refer to t he illust rat io n o n page 2 o f t his m anual.
1 DMX input
2 pow er supply input and f use ho lder
3 DMX o ut put
7 . Ope ra tion
The pro j ecto r st arts runnin g aft er co nnect io n to t he m ains.
The pro j ecto r has two running m o des: so und- act iv at ed stand- alo ne m o de and DMX m o de.

STAND-ALONE M ODE

Sound- Cont rol M ode
Set DIP sw it ches 1 to 10 to o ff. The pro jecto r feat ures a built - in m icro pho ne and w ill react to t he beat o f
t he am bient m usic. Adj ust t he sensit iv it y w it h t he ro t ary co nt ro l o n t he rear panel.
DMX M ODE
Set DIP sw it ch 1 0 to o n; set t he DMX address w it h DIP sw it ches 1 to 9 . Please refer to t he DMX address
reference chart o n page 3 .
Se ria l DM X Cha in
Co nnect an XLR cable t o t he fem ale 3- pin XLR o ut put o f yo ur co nt ro ller and t he o t her side t o t he m ale 3 -
pin XLR input o f t he pro j ecto r. Mult ip le pro j ecto rs can be link ed t hro ugh seria l link ing. The link in g cable
sho uld be a t wo- co re screened cable w it h XLR in put and o ut put co nnecto rs.
14. 05. 2014
VDPL3 0 0 M R
4 DIP sw it ches
5 ro t ary sensit iv it y co nt ro l
5
© Velleman nv