stayer SC2600W Instructions D'emploi page 17

Shut-off: Release the rectangular switch (15).
Start-up and shut-off when using the upper cutting table
(with automatic interlocking). Switches (16)
Start-up: Press the green button I.
Shut-off: Press the red button O
Use of the lower cutting table
Warning!
1
The risk of accidents due to a contact with the cutting
disk appearing at the upper table. For your own safety,
carry out the following preparation before working with
the lower table.
2
It is mandatory to carry out any settings with the cable
unplugged.
Safety setting of the upper cutting table for cutting
operations with the lower table
The mandatory requirement is that in the upper table the teeth
of the disc must not remain exposed. Cover the disc of the
upper table with the upper rectangular aluminium protector.
Link the two strapping bands in the back and front part of the
upper table. Ensure the fastening by tightening the black wing
nut for this purpose
WARNING
IF THE PROTECTOR IS NOT INSTALLED, THE MACHINE
WILL NOT WORK.
1 If the machine is in the down position, pull the pin (5) to
unlock the head (F) and lift it to its vertical position. If the
machine has a lower guard in place (2), remove it and
set it aside.
2 Loosen the table height adjustment screw (4B) and
use the adjustment screw (4A) to raise the table to its
maximum height.
Cutting operation with the lower cutting table
Warning!
1 Respect the limits regarding the size and material of the
workpiece.
2 Use clamps to fasten the workpiece whenever possible.
3 Never lock the motor power switch when working with the
lower cutting table.
Y
Preparation for horizontal angled cutting on the
lower table
To select the desired angle follow the steps below:Mitre
cutting (X axis = -45° / +45°, Y axis = 90°):
Y
Mitre cutting occurs when the head stays in a vertical position,
perpendicular to the lower cutting table. The head can rotate
on its axis from -45°to +45°.
To adjust the mitre angle, loosen the angle selector knob (1)
and use it to rotate the lower cutting table (A) to the desired
Y
angle.
The lower cutting table has a plate that marks the angle on
the scale ruler of the lower table. Once you have found the
desired cutting angle, tighten the angle selector knob (1).
In addition, the lower table is designed to allow easy angle
adjustment by intervals of 5°.
X
X
X
ENGLISH
17
To take advantage of these pre-sets, loosen the knob (1).
The table will continue to rotate as you push the knob (1) and
will stop automatically when it reaches any of the indicated
angles, halting at each angle until you engage the knob (1)
again.
Bevel cutting (X axis = 90°, Y axis = -45° / 0°):
Y
Y
Bevel cutting occurs when the head tilts on its axis and no
longer remains perpendicular to the lower cutting table. This
tool only allows the head to swing to the left side.
Before tilting the head, you must pull the pin on the lateral
guide (17) and deploy it by rotating it on its axis to facilitate
bevel cutting.
Y
To adjust the bevel cutting angle, loosen the head tilt
Y
adjustment knob (8) and tilt the head to the desired angle; the
machine is set up to tilt to 45º by default. Use the scale ruler
located next to the knob (8) to fine-tune the cutting angle.
Once you have found the bevel cutting angle, retighten the
knob (8).
Compound cutting (X axis = -45° / +45°, Y axis = -45° / 0°):
Y
Y
Compound cutting involves a combination of bevel and mitre
cutting angles. To find your compound cut, follow the steps
indicated for performing bevel and mitre cuts simultaneously.
Carrying out the cutting operation on the lower
table
1 Prepare workpiece by fastening it in a completely safe
manner.
2 Start the electrical machine by pushing switch.
3 Wait for some seconds until the cutting disk reaches its
maximum speed.
4
Slowly lower the operating head by a continuous manner
and without jerks, using hand grip.
5
Exert pressure in the blade's direction of advance with an
intensity being suitable for the material to be cut.
6
Once the cutting operation has been completed, raise
operating head again. Stop the machine by pushing
switch.
Using extension brackets (H) for long cuts
The tool includes 2 extension brackets (H) for cutting long
workpieces. The brackets are inserted into the slots (10) and
fastened by tightening the screw located on the lower table
near the slots. If the workpiece to be cut is long, users are
required to use the brackets for safety reasons.
Use as circular saw by means of the upper cutting
17
X
X
X
X
X
X