Assembly And Commissioning - Glatz PALAZZO Style/E Notice De Montage Et D'utilisation

Technical data Style/E
Closing height Passage height
Base without/with without/with Overall Minimum
Size area flounces flounces height weight
[cm] [m 2 ] [cm] [cm] [cm] [kg]
ø 350 8.7 179/154 235/210 356 180
ø 400 11.3 176/151 235/210 378 180
ø 450 14.3 178/153 235/210 406 180
ø 500 17.7 169/144 235/210 423 240
ø 600 25.5 149/124 235/210 455 310
350 x 250 8.8 123/98 235/210 337 180
350 x 300 10.5 133/108 235/210 362 180
400 x 200 8.0 100/75 235/210 322 180
400 x300 12.0 117/92 235/210 366 180
450 x 350 15.8 109/84 235/210 394 240
300 x300 9.0 142/117 235/210 353 180
350 x 350 12.3 124/99 235/210 371 240
400 x 400 16.0 121/96 235/210 405 240
450 x 450 20.3 103/78 235/210 422 310
Details when using the M4 ground * maximum wind speed when it is
socket securely anchored in the ground.
Colour temperature (built-in lighting) 3000 K
Maximum brightness (built-in lighting) 4500 to 5000 lumen, depending on the size
Technical data Noblesse/E
Closing height Passage height
Base without/with without/with Overall Minimum
Size area flounces flounces height weight
[cm] [m ] [cm] [cm] [cm] [kg]
2
ø 450 14.3 141/116 235/210 369 240
ø 500 17.7 138/113 235/210 392 240
ø 600 25.5 141/116 235/210 447 430
ø 700 36.8 103/78 235/210 460 570
450 x 350 15.8 112/87 235/210 397 240
500 x 250 12.5 91/66 235/210 374 240
500 x 400 20.0 101/76 235/210 422 310
550 x 450 24.8 85/60 235/210 442 430
600 x300 18.0 81/56 235/210 418 310
600 x 400 24.0 81/56 235/210 443 430
600 x500 30.0 82/57 235/210 476 430
400 x 400 16.0 121/96 235/210 404 310
450 x 450 20.3 98/73 235/210 417 430
500 x 500 25.0 84/59 235/210 439 430
550 x 550 30.3 88/55 235/210 472 570
600 x 600 36.0 81/56 235/210 512 570
Details when using the M4/M8 * maximum wind speed when it is
ground socket securely anchored in the ground.
Colour temperature (built-in lighting) 3000 K
Maximum brightness (built-in lighting) 5000 to 6500 lumen, depending on the size

Assembly and commissioning

maximum
• The appropriate remote control is tuned in to the parasol ex works.
wind speed*
• The power supply line must be provided by the customer on site. It must be
[km/h (Bft.)]
possible to disconnect this for installation and maintenance purposes and to
115 (11)
secure it against unintentional reconnection.
90 (10)
• Set up the connection between the power supply cable and the parasol by
75 (9)
means of the connecting plug supplied. The connector plug can be stowed
65 (8)
away either in the support tube or in the ground sleeve.
55 (7)
• For connection values see the section on Electrical supply.
100 (10)
• Secure all screws with medium-strength thread sealant (blue). When reassem-
95 (10)
bling, clean the screws or use new screws.
95 (10)
80 (9)
1
75 (9)
110 (11)
Unpacking the parasol
95 (10)
80 (9)
Supplied with:
70 (8)
- Parasol, binding belt, support tube or tip-
3×
over hinge, top, crank (not with motor variant)
5× 5×
or
- Mounting material for support tube or tip-
over hinge
- 4 support tube fastening screws
- 4 support screws
4×
- Cover to support tube or tip-over hinge
- Installation and operating instructions
- Safety bolt with lock
maximum
or
wind speed*
!
[km/h (Bft.)] Dispose of packaging material properly
85 (9) and keep away from children.
75 (9) Do not make use of defective material. In
the event of any damage, inform the
80 (9)
transport service provider immediately.
70 (8)
85 (9)
2
90 (10)
70 (8)
75 (9)
Placing the parasol down
80 (9)
!
Carefully place the parasol on a clean, hor-
75 (9)
izontal surface. The parasol is very heavy.
70 (8)
Work in a threesome and hold the parasol
95 (10)
securely.
80 (9)
70 (8)
75 (9)
65 (8) 3
3.1 Mount parasol top
1. Screw on top
20 21
4
Prepare ground fastening
!
Remove the protective cover, place the ground sleeve
according to the separate instructions. Observe weights
for base and wind resistance. Note the final alignment of
the parasol (NB notch)!
if mounting with support tube...
5
5.1 5.5
Pre-assemble support tube
1. Place support tube on ground fastening
2. Make sure the notches are aligned
5x
3. Using the 5 stud screws, ensure that the
support tube is vertically aligned
5x
5×
4. Place 5 support screws
5×
5. Pre-assemble support tube with 5 fastening
screws
4×
4×
6
6.2
Prepare set up
1. Slide on the support tube cover
2. Establish plug connection. Observe the
polarity of the plug
!
Position power cable so there is no strain
on it. Ensure that the cable is not pinched.
6.1
7
7.1 Set up parasol
1. Lift parasol over the support tube and lower
it carefully
2. Tighten the two lower screws (56 Nm)
3. In case of need, secure parasol against theft
with a lock
4. Align parasol, then tighten the 5 fastening
screws crosswise (32 Nm)
5. Lower support tube cover
6. Tighten the two upper screws (56 Nm)
!
7.6 Ensure that the electrical cable is not dam-
aged or pinched.
7.2 7.2
7.5
7.3
!
The parasol is very heavy. Work in a three-
some and hold the parasol securely. Ensure
that the electrical cable is not damaged or
pinched.
if mounting with tip-over hinge...
5
5.1 5.3
Pre-assemble the tip-over hinge
1. Slide on the hinge cover
2. Loosen / remove fixing bar
3. Slide on press ring
4. Place the tip-over hinge on the ground
5.6
fastening (tilt hinge under the crank handle)
5.7
5.5
5. Pre-fix the tip-over hinge on the floor
fastening with 3 clamping blocks
6. Remove 2 locking screws
7. Tilt the tip-over hinge sideways
6
6.1
6.2
Connect the parasol with the hinge
1. Lead the cable through the hinge
2. Slide the parasol over the tip-over hinge
6.5
3. tighten 2 lower screws (56 Nm)
4. Establish plug connection. Observe the
polarity of the plug
5. Carefully erect the parasol
6.3
6.6
6. Tighten 2 locking screws (6 Nm)
6.4
!
Make sure that the electrical cable is not
damaged or pinched. Plug position cen-
tered with tip-over hinge.
7
Completing the assembly
1. Align parasol, tighten the 3 clamping
blocks (32 Nm)
2. Lower the press ring, tighten (32 Nm)
3. Lower the hinge cover
4. Tighten 2 upper screws (56 Nm)
7.4
7.2
5. If necessary, secure the parasol under hinge
cover with lock to prevent theft
7.3
!
Realign the parasol: Remove press ring,
slightly loosen clamping blocks and fasten-
ing screws, adjust leveling screws, tighten
everything again.