Product Information; Safety Instructions - Hilti GX 2 Mode D'emploi Original

Masquer les pouces Voir aussi pour GX 2:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

‚ ‛
Description of marked operating controls on the fastening tool
« »
Markings on the fastening tool

1.4 Product information

Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained
personnel or if used not in accordance with the intended use.
The type designation and serial number are stated on the rating plate.
▶ Write down the serial number in the table below. You will be required to state the product details when
contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
Fastening tool, gas-
actuated
Generation:
Serial number:
2 Safety

2.1 Safety instructions

Working safely with the fastening tool
▶ Pressing the nosepiece of the fastening tool against a part of the body may lead to serious injury due to
inadvertent actuation and release of a fastener. Never press the nosepiece of the tool against your
hand or any other part of the body.
▶ When inserting/loading application-specific fasteners (e.g. washers, clips or clamps, etc.) in/on the
fastener guide there is a risk of serious injury due to inadvertent actuation of the tool resulting in
discharge of a fastener. When inserting/loading an application-specific type of fastener, never press
a hand or any other part of the body against the fastener guide.
▶ Never point the fastening tool towards yourself or any other person.
▶ Keep your arms flexed when operating the tool (do not straighten the arms).
▶ When pulling back the nail pusher, always take care to ensure that it engages.
▶ When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward
slowly. There is a risk of pinching the fingers.
▶ Do not attempt to drive fasteners into materials that are too hard, such as welded steel or cast steel.
Attempting to drive fasteners into these materials may lead to malfunctions, incorrectly driven fasteners
or breakage of fasteners.
▶ Do not attempt to drive fasteners into materials that are too soft, such as wood or drywall/gypsum
board. Attempting to drive fasteners into these materials may lead to malfunctions and fasteners being
driven incorrectly or driven right through the material.
▶ Do not attempt to drive fasteners into materials that are too brittle, such as glass or tiles. Attempting
to drive fasteners into these materials may lead to malfunctions, fasteners being driven incorrectly and
may cause the material to shatter.
▶ Before driving fasteners, check that there is no risk of injuring persons or of damaging objects present
behind or below the working surface.
▶ Pull the safety trigger only when the fastening tool is pressed against the working surface in such a way
that the fastener guide is pushed into the tool as far as it will go.
▶ Always wear gloves if you have to carry out maintenance work on the fastening tool while it is still
hot.
▶ If fasteners are driven at a high rate or if the tool used for a long period, surfaces of the tool beyond the
grip areas may get hot. Wear protective gloves to avoid burning injuries.
▶ If the fastening tool overheats, remove the gas can and allow the tool to cool down. Do not exceed the
specified maximum fastener driving rate.
▶ Driving fasteners may cause flying fragments or result in parts of the nail strip material being forcibly
ejected from the tool. Flying fragments present a risk of injury to the body and eyes. Wear eye
protection, ear protection and a hard hat. Depending on the application and type of fastening tool in
use, wearing personal protective equipment such as a dust mask, non-slip safety footwear, hard hat and
2
English
Printed: 11.09.2017 | Doc-Nr: PUB / 5373611 / 000 / 00
GX 2
01

Publicité

Table des Matières
loading

Table des Matières