Emptying Detergent Solution; Emptying Device Detergent Solution (Optional); Forward Movement; Stop - ADIATEK ruby 45e Emploi Et Entretien

GB

EMPTYING DETERGENT SOLUTION

To empty the detergent solution remained in the so-
lution tank:
1. Bring the machine to an appropriate place for
tanks draining.
2. Unscrew the exhaust plug (1).
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.
EMPTYING DEVICE DETERGENT SOLUTION (OP-
TIONAL)
To recover the detergent solution, it is necessary to
use the emptying device provided for the purpose
and proceed as follows:
1. Unhook the hose.
2. Open the solution valve directing the jet into a
collecting container.
3. When the operation has been completed, close
the solution valve.
Put the hose back into its position, placing it into
the spring.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

FORWARD MOVEMENT

The traction of these machines is given by the
brushes that, working on an inclined axle, transmit
to the machine the forward movement. The effect is
bigger with brushes that have thicker bristles.

STOP

Releasing the lever of the presence, brushes rotation
will end, stopping the machine movement.
ATTENTION:
Moving the machine backwards, make sure that the
squeegee is lifted.

ADJUSTMENT BRUSHES INCLINATION (OPTIONAL)

Through the register (1) placed on the brushes base
group, it is possible to adjust the brushes inclination
increasing/decreasing the speed of the machine. A
label placed on the brushes base indicates the ad-
justment levels LOW/FAST.
STOP OF THE MACHINE AFTER
CLEANING OPERATION
Before executing any type of maintenance:
1. Close the solution valve through the lever (10).
2. For machines optionally equipped with solenoid
valve (see under "OPTIONAL ACCESSORIES") the flow
of detergent solution will stop automatically when
the levers (9) are released. On the instrument board
the signal lamp of the open solution valve will go off
(6).
3. Lift the brushes base acting upon the pedal (12).
4. Lift the squeegee acting upon the lever (11).
5. Turn the brushes motor switch off (1).
6. Turn the suction motor switch off (2).
7. Take off the plug from the mains socket.
8. Bring the machine to an appropriate place for
tanks draining.
ATTENTION:
The machine is not equipped with a parking brake,
therefore do not leave it on slopes.

DAILY MAINTENANCE

RECOVERY TANK CLEANING

1. Hold the exhaust hose placed in the front part of
the machine.
2. Take off the exhaust plug acting upon its lever
and empty the recovery tank into appropriate con-
tainers (see under "OVERFLOW DEVICE").
3. Take off the suction cover (1) after rotating the
blocking levers (2).
4. Take off the filter and filter protection.
5. Rinse the tank with a water jet.
19
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

SUCTION FILTER CLEANING

1. Take off the suction cover (1) after rotating the
blocking levers (2).
2. Take off the filter and filter protection.
3. Clean all parts with a water jet especially inside
surfaces and filter bottom.
4. Carry out carefully the cleaning operations.
5. Reassemble all parts.

BRUSHES CLEANING

Disassemble the brushes and clean them with a wa-
ter jet (for the brushes disassembly, check "BRUSHES
DISASSEMBLY" paragraph).

BRUSHES DISASSEMBLY

ATTENTION:
Check that the plug is disconnected.
1. Lift the brushes base lowering the pedal (12).
2. With the brushes base in lifted position, turn the
brush in its rotating sense, until it is released from
the brush holder plate seat as indicated in the figure.
The figure shows the rotating sense for brushes re-
lease.
GB