14
4.02
Safety functions
Use of brakes
Apply the brake by stepping on the lower part of pedal, marked
with red. Release the brake, by stepping the top part of pedal,
marked with green. Both center wheels are locked when stepping
on the lower part of pedal.
Adjustment of knee pad
The knee pad can be adjusted
in vertical direction to fit the
different users. Make the knee
pad adjustable by pushing
and holding the button on the
backside of the knee pad. To
lock the knee pad, release the
button and adjust until you
hear a click.
5 .00
Cleaning and disinfection
We recommend that the products and the parts patients and car-
egivers can come in contact with, are cleaned with a damp cloth
using warm water and a mild soap solution.
When disinfection is needed, use disinfectant wipes with up to a
85% solution of isopropyl, or a damp cloth using warm water and
a disinfectant cleaner, e.g. an chlorine dissolving up to 1500 ppm.
If other chemicals and/or liquids with higher resolution should be
used to clean or disinfect these products, please contact Guld-
mann providing the item´s safety sheet chemical composition for
consideration.
Caution: Take great care to ensure that no liquids get inside the
transfer platform. The transfer platform is not waterproof. Failure
to protect the transfer platform from liquids may result in damage
to the transfer platform and/or may cause personal injury.
6 .00
Service and lifetime
The transfer platform has an expected life span of 10 years. The
lifespan is estimated on the basis of correct use, cleaning and
maintenance, plus annual service and maintenance carried out
by qualified technician. At the end of the expected lifespan, the
transfer platform must then be assessed by qualified service staff
as to the transfer platforms future use.
No part of the equipment shall be serviced when in use.
Worn or defective parts shall be replaced by new spare parts from
V. Guldmann A/S.
Spare parts lists and drawings are available from manufacturer or
supplier.
6 .01
Service check – All-round
Guldmann recommends that the transfer platform is service
checked yearly, according to:
1 . Visual check of the product
Check the product for wear and tear
Check the product for any deformity
Check that the product does not show any other deficiencies
2 . Test of the product, as during normal use
Check all functions on the product, with and without load
(e.g. Knee pad up/down, brake lock/unlock, wheels are mov-
ing freely)
3 . Check the mechanical condition of the product
Clean the product for dirt and other impurities
Inspect and evaluate the vital parts of the product
Exchange defective and worn parts of the product
Check and tighten all moving parts
4 . Point 2 is carried out one more time as a control function
5. Have new errors or problems arisen in point 4?
If new problems have arisen, go back to point 2
If no problems have arisen, finish the inspection
6.02
Owners daily maintenance
The owners' daily maintenance consists of general cleaning. Re-
move hair and the like from wheels. Make sure that they are able
the rotate freely. Test that the brake functions properly.
6 .03
Troubleshooting
Error:
The transfer platform is not able to move
A. Do the wheels rotate and move freely?
Yes: See point B
No:
Clean the wheels and remove hair and the like
or replace with new spare parts
B. Is the brake activated?
Yes: Release the brake
No:
See point A
Contact the Guldmann Service Team if the fault cannot be found
and corrected.
7 .00
Environmental conditions
Operation
The products operational environment:
–
Operation temperatures between +10°C and +40°C
(50°F and 104°F)
–
A relative air humidity of between 30% and 70%
–
An air pressure of between 700 hPa and 1060 hPa
Information is illustrated by symbols on packaging including:
–
Fragile
–
This side up
Beside temperature, the same environmental conditions apply for
transportation and storage.
Symbols on the packaging:
70%
40ºC
104ºF
-10ºC
30%
70 kPa
14ºF
Transportation and storage
The transfer platform can be dismantled for transport and storage.
106 kPa