Counters Page; User; Main Menu; Password Access - LOVATO ELECTRIC DMG800 Manuel D'application

Masquer les pouces Voir aussi pour DMG800:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

COUNTERS P GE
– The counters page displays CNT1...4 counters.
– It is possible to count the number of times an input is activated, or a limit has been overcame etc. The count condition is defined by Counter source
parameters.
– For every counter, it is possible to define a description and a unit of measure with a free text, for instance litres, kg, etc.
– It is possible to define a conversion factor between the number of pulse counts and the measurement shown on display. This function can be obtained by
specifying a multiply and a divide factor. For instance, setting the multiplier k to 3, for every pulse count, the value shown will be incremented 3 times. If
instead, a divider is set to 10, then the value will be incremented by one only after 10 pulses have been applied to the input. With a combination of multiply
and divide factor, any ratio between counts and measurement can be achieved.
– If the counter has no divide factor, the screen will indicate the counter without fractional digits, otherwise the counter will be displayed with two decimal
digits.
– The counters can be cleared by means of commands menu or by means of the Reset source signal, defined by dedicated parameters.
1 - Unit of measure (free text)
2 - Count
3 - Description (free text)
4 - No. of the selected counter
USER P GES
– The user can create a maximum of
4 customised display pages.
– Each of these pages can view
4 measurements, freely chosen among the available readings of the DMG800.
– The title of the page can be freely programmed by the user, allowing, for instance, indicating the part of the plant supervised by the multimeter.
– The user pages are placed in a position that allows to reach them easily starting from the first page, by pressing button s.
– Like all other pages, it is possible to set the multimeter to return automatically to the user page after a time has elapsed without keystrokes.
– To define the user page, see the dedicated menu M15 in the parameter setup chapter.
M IN MENU
– The main menu is made up of a group of graphic icons (shortcuts) that allow rapid access to measurements and settings.
– Starting from normal viewing, press MENU key. The main menu screen is displayed.
– Press s t to select the required function. The selected icon is highlighted and the central part of the display shows the description of the function.
– Press
to activate the selected function.
– If some functions are not available, the correspondent icon will be disabled, that is shown in a light grey colour.
etc. - Shortcuts that allow to jump to the first page of that group. Starting from that page it is still possible to move
forward-backward in the usual way.
- Open the password entry page, where it is possible to specify the numeric codes that unlock protected functions (parameter setting, commands
menu, etc.).
- ccess point to the set-up menu for parameter programming.
- ccess point to the commands menu, where the authorised user can execute some clearing-restoring actions.
1 - Voltage readings
2 - Current readings
3 - Power readings
4 - Frequency - symmetry
5 - Harmonic nalysis
6 - Energy meters
P SSWORD CCESS
– The password is used to enable or lock the access to the setting menu (set-up) and to commands menu.
– For brand-new devices (factory default), the password management is disabled and the access is free.
If instead the passwords have been enabled and defined, then to get access it is necessary to enter the password first, specifying the numeric code through
the keypad.
– To enable password management and to define numeric codes, see setup menu.
– There are two access levels, depending on the code entered:
• User-Level access - llows clearing of recorded values but not editing of set-up parameters.
• dvanced access level - Same rights of the user access plus settings editing-restoring.
– From normal viewing, press MENU to recall the main menu, select the password icon and press
– The display shows the screen in the figure.
7 - Trend graph
8 - Hour readings
9 - Expansion modules
10 - Set-up menu
11 - Commands menu
12 - Password entry
.
G
B
5

Publicité

Table des Matières
loading

Table des Matières