LOVATO ELECTRIC DMG800 Manuel D'application page 14

14
M12 - BOOLE N LOGIC
P12.n.01 Operand 1
P12.n.02 Channel number (x)
P12.n.03 Logic operator 1
P12.n.04 Operand 2
P12.n.05 Channel number (x)
P12.n.06 Logic operator 2
P12.n.07 Operand 3
P12.n.08 Channel number (x)
P12.n.09 Logic operator 3
P12.n.10 Operand 4
P12.n.11 Channel number (x)
Note: this menu is divided into 8 sections, for Boolean variables BOO1..8
P12.n.01 = First operand of the Boolean logic.
P12.n.02 = Number of the channel (x) referred to previous parameter.
P12.n.03 = Logic operation between first and second operands.
P12.n.04 = Second operand.
From P12.n.05 to P12.n.11 – (see above).
M13 - INPUTS
P13.n.01 Input function
P13.n.02 Normal status
P13.n.03 ON delay
P13.n.04 OFF delay
Note: this menu is divided into 8 sections, for digital inputs INP1..8
P13.n.01 = Input function:
OFF – Input disabled
ON – Input enabled, used as a source for counters, Boolean logic, etc.
LOCK – Settings lock. Does not allow access to both levels.
SYNC – Synchronisation for power/energy integration.
T R- , T R-B – Energy tariff selection. See Energy tariffs chapter.
C01...C08 – When this input is activated (edge-triggered), the correspondent command from the command menu is executed.
P13.n.02 = Normal status of the input. llows to invert the INPn activation logic.
P13.n.03 – P13.n.04 = Delay on activation – deactivation of the input. llow to filter the input status to avoid bouncing.
M14 - OUTPUTS
P14.n.01 Output function
P14.n.02 Channel number (x)
P14.n.03 Idle status
Note: this menu is divided into 8 sections, for digital outputs OUT1..8
P14.n.01 = Function of the output:
OFF – Output disabled
ON – Output always enabled
SEQ – Output enabled in case of wrong phase sequence
LIMx – BOOx – L x – PULx – REMx – Output linked to the status of the programmed variable. llows to connect the status of an output to the status of a limit
threshold, a Boolean variable, an alarm, etc.
P14.n.02 = Number of the channel (x) referred to previous parameter.
P14.n.03 = Normal status of the output. llows to reverse the logic of the output function.
M15 - USER-DEFINED P GES
P15.n.01 Page enabling
P15.n.02 Title
P15.n.03 Measurement 1
P15.n.04 Measurement 2
P15.n.05 Measurement 3
P15.n.06 Measurement 4
Note: this menu is divided into 4 sections, for user pages P G1..4
P15.n.01 = Enables user page P Gn.
P15.n.02 = Title of the user page. Free text, 16 chars.
P15.n.03, P15.n.04, P15.n.05, P15.n.06 = Measurement that will be shown in the four frames of the user page.
Default Range
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
- - - - - - - ND - OR - EXOR - ND NOT -
OR NOT - EXOR NOT
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
- - - - - - - ND - OR - EXOR - ND NOT -
OR NOT - EXOR NOT
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
- - - - - - - ND - OR - EXOR - ND NOT -
OR NOT - EXOR NOT
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
UdM Default Range
OFF OFF - ON - LOCK -
SYNC-T R- - T R-B
C01...C08
OFF OFF-ON
sec 0.05 0.00 - 600.00
sec 0.05 0.00 - 600.00
UdM Default Range
OFF OFF-ON-SEQ-LIMx-
BOOx- L x-PULx-
REMx
1
OFF OFF-ON
Default Range
OFF OFF - ON
P Gn (Text - 16 char)
OFF OFF- (measurements)
OFF OFF- (measurements)
OFF OFF- (measurements)
OFF OFF- (measurements)
G
B
1 - 8