Tivoli Audio MUSIC SYSTEM BT Manuel Utilisateur page 8

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 60
(maximum output). If the volume ever sounds distorted, reduce the level immediately. In any
mode, push and hold the knob to access the menu. See section marked "Menu". Push in and
rotate counter-clockwise to reduce the treble or clockwise to increase the treble. Press the
volume knob in to set or the setting will store automatically and the display will return to its
previous state. This knob is also used to adjust and enter selections (by pushing the knob in)
when setting the Clock and Alarms. Adjusting the volume during Snooze will cancel the Snooze
mode.
13. AUDIO: Push briefly to cycle through Stereo, Wide mode, or Mono audio settings. The Wide
mode setting is designed to create a more expansive soundstage, while the Mono setting
reduces multiplex noise on weak FM stations, making otherwise unlistenable stations listen-
able. Regardless of the previous audio setting, the Wide mode will automatically engage each
time the Music System BT is turned on.
EQ: To temporarily turn the EQ off, press and hold the Audio button. The display will show "EQ
Off" and a confirmation beep will sound. The EQ will engage again automatically the next time
the Music System BT is turned on. To keep the EQ off, press and hold the Audio button and
the display will show "EQ Always Off" and a confirmation beep will sound. The EQ will remain
off until "EQ On" is selected. The EQ differs from Audio in that it enhances lower frequencies
primarily at lower volume levels. We suggest the rear Bass level be set to the center detent
position. Should the bass ever sound distorted, immediately lower the bass level and/or volume.
For more, see the section marked "Getting the most from your Music System BT."
14. DISPLAY: When in FM mode, briefly press repeatedly to select between RDS Scrolling Text,
(Figure 11), Static Text, or RDS Off. If a station is not broadcasting in RDS or the RDS signal is
too weak, no RDS text will be shown. In cases where the signal is weakly received the text
may be scrambled. Note the AM band does not utilize RDS text. For more, see "Reception/
RDS". RDS text will not be shown in Sleep mode. When playing a CD, press repeatedly to
select between CD Scrolling Text, Static Text, or CD Text Off. If the inserted CD does not
contain CD text (Figure 12), then this feature cannot be enabled. Not all commercial music CDs
contain CD Text. CD text will not be shown in Sleep mode.
Fig 11, 12
15. SNOOZE/MUTE (Top of Cabinet): When the Alarm activates, press this button to silence the
alarm for 7 minutes. The display will count down the remaining Snooze time. Adjusting the
volume level will cancel the Snooze mode. During normal operation, press this button to mute
the audio. The display will show "Muted". Press again to restore the audio output or adjust the
volume level.
16. HEADPHONE OUT: Connect a set of headphones (not included) to this variable stereo output for
private listening. Plugging in the headphones will mute the primary speakers. The headphone's
volume is adjusted using the front panel volume knob. This stereo output accepts a 3.5 mm stereo
male mini connector. Avoid using headphones at high volume levels to prevent possible hearing
damage.
17. IR SENSOR: Receives signals from the included remote control. Do not obstruct this sensor.
18. SLOT-LOAD: Insert a disc (with printing side facing up) until it is drawn inside. The display will
say "Loading". Disc functions will not work while the disc is loading. Playback will begin auto-
matically once the table of contents is read. The display will show "No Disc" when the unit is
set to CD mode and there is no CD inside. When ejecting a CD the display will show "Ejecting".
For more, see "Important Notes About the CD Player."
8 – ENGLISH

Publicité

Table des Matières
loading

Table des Matières