Mechanical Installation - JB Systems Light LED LIGHTBAR 4TC Mode D'emploi

ENGLISH
 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 The housing and the lenses must be replaced if they are visibly damaged.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don't use the effect in the presence of persons suffering
from epilepsy.

MECHANICAL INSTALLATION

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
BUILDING TOGETHER AND INSTALLING ON A LIGHT STAND:
When the LED LIGHTBAR 4TC is installed on top of a light stand, make sure to choose a stand with
the adapted specifications: excellent stability, adapted load capacity to hold the bar safely, etc.
 If the product is not assembled yet, unpack all parts and put them on a table.
 Assemble the 4 projectors as follows:
 On the metal bar you will see 4 holes: put the projector in front of the hole on the bottom of the bar and
push the bolt from the bottom up. Keep the following order during the assembly:
 Bolt (C)
 Leather washer (B)
 Projector with its bracket (D)
 Leather washer (B)
 LIGHT BAR
 Leather washer (B)
 Wing nut (A)
 Repeat this action for the 4 projectors. (refer to the drawing to see how the 4
panels should be fixed correctly)
 Insert the LED power cable (G) in the back of the four corresponding panels.
 When the 4 panels are fixed to the 4bar, open the knob of the 35mm adapter (15)
and put the assembled LED LIGHTBAR 4TC on top of a stable light stand (not
included).
 Tighten the knob of the adapter (15) and connect all cables (see later)
 You can still align the panels in different directions.
 Done!
JB SYSTEMS
®
OPERATION MANUAL
3/64 LED LIGHTBAR 4TC
ENGLISH
DESCRIPTION:
1. Mains input: with IEC socket and integrated fuse holder, connect the supplied mains cable here.
2. Mains output: with female IEC socket, used to daisy chain the power of several units.
IMPORTANT: you can daisy chain the 230V power of maximum 10units (660Watt)!
3. DMX input: connect to a DMX controller or to the DMX-output of the previous DMX-unit in the line.
4. DMX output: connect to the DMX-input of the next DMX-unit in the line.
5. Foot controller input: can be used to connect our optional CA-32F foot controller.
6. CA-8 input: ¼" Jack input for the optional CA-8 hand controller
7. Internal microphone: needed to synchronize the chases to the rhythm of the music.
8. Slave LED: is lit when the unit is in slave mode
9. Sound LED: blinks to the rhythm of the music while the unit is in audio mode
10. DMX LED: is lit when the unit receives a DMX-signal
11. Master LED: is lit when the unit is switched as master (internal chases)
12. MENU button: used to select the different menu items
13. DOWN button: to go back in the menu and to lower the values shown on the display.
14. UP button: to go up in the menu and to increase the values shown on the display.
15. ENTER button: used to confirm your choice.
16. DISPLAY: shows the various menus and the selected functions.
17. 35mm STAND ADAPTER: used to put the LED LIGHTBAR 4TC easily on top of a light stand
18. Special cables with LED power signal for the passive LED panels
19. Passive LED panels: each containing 4 RGB 3Watt LEDs.
HOW TO SETUP:
MAIN MENU:
 Press the MENU button until the required option is shown on the display.
 Select the desired function with the ENTER button. The display will blink.
 Use DOWN and UP button to choose the desired menu option.
 Once the required menu option is selected, press the ENTER button to confirm.
To go back to the functions without any change press the MENU button for about 2 seconds or just wait 8
seconds. The menu structure is shown below.
DMX512 Address Setting
Used to set the starting address in a DMX setup.
 Press the MENU button until Addr is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to change the DMX512 address.
 Once the correct address shows on the display, press the ENTER button to save it.
 Press the MENU button for about 2 seconds to save the settings and return to normal working mode. (or
automatically return to the main functions without any change after 8 seconds)
JB SYSTEMS
®
OPERATION MANUAL
4/64 LED LIGHTBAR 4TC