Spare Parts List; Disposing Product; Emc Information (Electromagnetic Compatibility Information) - NSK ENDO-MATE AT Mode D'emploi

19

Spare Parts List

Model
F-type Spray Nozzle
20

Disposing product

In order to avoid the health risks of operators handling the disposal of medical equipment, as well as the risks
of environmental contamination caused thereof, a surgeon or a dentist is required to confirm the equipment is
sterile. Ask specialist firms who are licensed to dispose of specially controlled industrial wastes, to dispose the
product for you.
21

EMC Information (Electromagnetic Compatibility Information)

Guidance and manufacturer's declaration - Electromagnetic Emissions
The product is intended for use in the electromagnetic environment specified below. The customer or the user of the product should assure that is used in such an
environment.
Emissions test
RF emissions
CISPR11/EN55011
RF emissions
CISPR11/EN55011
Harmonic emissions
EN/IEC61000-3-2
Voltage fluctuations/flicker emissions
EN/IEC 61000-3-3
Guidance and manufacturer's declaration - Electromagnetic Immunity
The product is intended for use in the electromagnetic environment specified below. The customer or the user of the product should assure that is used in such an
environment.
Immunity test EN/IEC60601 test level
Electrostatic discharge (ESD) ±(2, 4) 6kV contact
EN/IEC61000-4-2 ±(2, 4) 8kV air
Electrical fast transient/burst ±2kV for power supply lines
EN/IEC61000-4-4 ±1kV for input/output lines
Surge ±1kV line(s) to line(s)
EN/IEC61000-4-5 ±2kV line(s) to earth
Voltage dips, short <5% Ut (>95% dip in Ut)
interruptions and voltage for 0.5 cycles
variations on power supply
40% Ut (60% dip in Ut)
input lines
for 5 cycles
EN/IEC61000-4-11
70% Ut (30% dip in Ut)
for 0.5 cycles
<5% Ut (<95% dip in Ut)
for 5 sec
Power frequency 3 A/m
(50/60Hz)magnetic field
EN/IEC61000-4-8
NOTE: 'Ut' is the AC mains voltage prior to application of the test level.
Order Code
Z256090
Compliance Electromagnetic environment - guidance
Group 1 The product uses RF energy only for its internal function. Therefore, its RF emissions are very low
and are not likely to cause any interference in nearby electronic equipment.
The product is suitable for use in all establishments, including domestic establishments and those
Class B
directly connected to the public low-voltage power supply network that supplies buildings used for
domestic purposes.
Class A
Applicable
Compliance level
±(2, 4) 6kV contact
±(2, 4) 8kV air
±2kV for power supply lines
±1kV for input/output lines
±1kV line(s) to line(s)
±2kV line(s) to earth
<5% Ut (>95% dip in Ut)
for 0.5 cycles
40% Ut (60% dip in Ut)
for 5 cycles
70% Ut (30% dip in Ut)
for 0.5 cycles
<5% Ut (<95% dip in Ut)
for 5 sec
3 A/m
Electromagnetic environment - guidance
Floors should be wood, concrete or ceramic tile. If floors are
covered with synthetic material, the relative humidity should
be at least 30%.
Mains power quality should be that of a typical commercial
or hospital environment.
Mains power quality should be that of a typical commercial
or hospital environment.
Mains power quality should be that of a typical commercial
or hospital environment. If the user of the product requires
continued operation during power mains interruptions, it is
recommended that the product be powered from an
uninterruptible power supply or a battery.
Power frequency magnetic fields should be at levels
characteristic of a typical location in a typical commercial or
hospital environment.
7