Recording The Alarm Data On The Tape - Sony SVT-96LP Mode D'emploi

When the alarm data reaches more than 100
The oldest one will be erased.
To reset the alarm data
Press MENU RESET while the ALARM DATA menu
is on the screen.
The alarm count shows "000".
Recording the Alarm Data on the
Tape
1
1
Turn on the power of the equipment to be used.
2
Press MENU and MENU V until "3" of the MAIN
MENU flashes on the monitor screen.
3
Press MENU B.
The ALARM SET menu appears.
ALARM SET
ALARM MODE
ALARM SPEED
ALARM DURATION
ALARM DATA REC
TAPE END WARN.
CLOG DETECTION
SERIES REC
< >
NEXT PUSH
+ –
SELECT : DATA SET : / RETURN : MENU
4
Press MENU V to move the flashing to the setting
of ALARM DATA REC and set to ON by pressing
MENU + or –.
ALARM SET
ALARM MODE
ALARM SPEED
ALARM DURATION
ALARM DATA REC
TAPE END WARN.
CLOG DETECTION
SERIES REC
< >
NEXT PUSH
+ –
SELECT : DATA SET : / RETURN : MENU
2-4 5
A1
6H
20sec
OFF
COUNTER
ON
OFF
A1
6H
20sec
ON
COUNTER
ON
OFF
ON (in recording mode): when the recording
comes to the end, the VCR rewinds the tape to
the beginning and starts recording the alarm data
on the ALARM DATA menu up to 100 data.
ON (in playback mode):
1 When the tape is inserted, the VCR rewinds
the tape to the beginning.
2 Press SEARCH until "AL L" flashes in the
display window.
3 Press REW m.
The ALARM DATA list appears.
To change the page of the ALARM DATA,
press FF M or REW m. (You may have
to press the button a few times.)
In the display window
ALARM DATA
1 0 0 . 0 3 – 1 2 1 9 : 0 0 9 0 . 0 0 – 0 0
9 9 . 0 1 – 1 1 2 3 : 0 0 8 9 . 0 0 – 0 0
9 8 . 2 5 – 1 0 1 5 : 0 0 8 8 . 0 0 – 0 0
9 7 . 2 5 – 1 0 0 8 : 0 0 8 7 . 0 0 – 0 0
9 6 . 2 5 – 1 0 0 6 : 0 0 8 6 . 0 0 – 0 0
9 5 . 0 0 – 0 0 0 0 : 0 0 8 5 . 0 0 – 0 0
9 4 . 0 0 – 0 0 0 0 : 0 0 8 4 . 0 0 – 0 0
9 3 . 0 0 – 0 0 0 0 : 0 0 8 3 . 0 0 – 0 0
9 2 . 0 0 – 0 0 0 0 : 0 0 8 2 . 0 0 – 0 0
9 1 . 0 0 – 0 0 0 0 : 0 0 8 1 . 0 0 – 0 0
NEXT DATA:
On the monitor
4 Press MENU + or – to set the alarm count and
then press FF M.
The tape runs to the set alarm count and the
playback picture appears in the still mode.
Example:
To go to the 11th alarm count
Press MENU + or – to display 11 and press
FF M. The alarm count in the display window
counts down and becomes 00 after 10.
To go to the 15th alarm count after going to
the 11th
Press MENU + or – to display 04 and press
FF M until 00 appears.
To go back to the 7th alarm count after going
to the 11th
Press MENU + or – to display 04 and press
REW m until 00 appears.
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
0 0 : 0 0
RETURN : MENU
37